曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

INTEGRATED
AIR SYSTEM
CONTROLLER
DISTRIBUTION
INDICATING
SUPPLY
BLEED
AIR
SYSTEM
(IP)
BLEED
AIR
SYSTEM
(HP)
ENGINES
APU
REV 1
AIR CONDITIONING/PRESSURIZATION
Volume 2 Flight Crew Operating Manual Sep 13/2004
02-02-02 CSP 100-6 REV 1
BLEED AIR DISTRIBUTION
DESCRIPTION
Air for operation of the aircraft IP bleed air system is distributed by a common manifold. Bleed air management, which
consists of bleed source selection, valve operation, and air distribution, is controlled by two integrated air management system
controllers (IASC).
The aircraft IP bleed air system is controlled from the AIR COND/BLEED panel. Cabin and cockpit temperatures controls
range from 15 °C to 35 °C in normal mode and 10 °C to 70 °C in manual mode.
AIR SOURCE
NORM
OFF PACK ONLY
AIR COND / BLEED
TRIM AIR
ONLY
COCKPIT
COLD HOT
RAM AIR
ON
XBLEED R BLEED
OFF
MAN TEMP
ON
CABIN
COLD HOT
APU
ON
L BLEED
OFF
CFO0202002_003
AIR CONDITIONING/PRESSURIZATION
Sep 13/2004 Flight Crew Operating Manual Volume 2
REV 1 CSP 100-6 02-02-03
BLEED AIR DISTRIBUTION (Cont)
COMPONENTS AND OPERATION
BLEED AIR MANIFOLD
The bleed air manifold is located in the engine pylons and aft equipment bay and is divided into the right side and left side
by the crossbleed (XBLEED) valve. The engines provide bleed air to their respective sides of the manifold and the APU
and ground air cart provide air into the right side of the crossbleed valve.
EXTERNAL GROUND AIR CONNECTOR
An external air connector is located aft of the equipment bay door on the exterior surface of the fuselage.
The external ground air connector and duct are not depicted on the ECS synoptic displays. However, when external air is
connected, the air pressure is displayed as a manifold pressure digital readout on the ECS synoptic page.
CHECK VALVES
Four check valves are installed in various locations in the bleed air ducting.
An intermediate pressure check valve is installed in each engine bleed air duct to prevent reverse flow into the engines.
Check valves are installed at the external air connector and in the APU bleed air duct. The check valve at the external connector
prevents the loss of air to the atmosphere. The check valve in the APU duct prevents the reverse flow of manifold
air to the APU when the APU is shut down.
Check valves are not represented on the ECS or A/ICE synoptic displays.
INTERMEDIATE PRESSURE VALVES
Engine bleed air pressure increases proportionally with N2 compressor speed. The pressure regulating function of the intermediate
pressure valve limits the engine discharge pressure to 50 ± 3 psi. When N2 compressor speed is low and the
engine bleed air pressure is less than the regulated value, and at least 10 psi or greater, the valve is fully open.
The valves are pneumatically operated and electrically controlled by the L (R) BLEED switches on the air cond/bleed panel.
The bleed air valves are in a closed position when:
- Aircraft engines are shutdown
- Power is lost to valves
- Associated ENG FIRE switch is selected
- Bleed air valves are selected closed at the AIR COND/BLEED control panel.
HIGH PRESSURE VALVES
The high pressure valves regulate the engine high pressure bleed to 36 ± 3 psi. This high pressure air is then routed to the
wing anti-ice system.
The valves are pneumatically operated and electrically controlled by the WING SOURCE switch and WING switch on the
ANTI-ICE control panel.
The high-pressure valves are in a closed position when:
- Aircraft engines are shutdown
- Power is lost to valves
- Associated ENG FIRE switch is selected
- Bleed air valves are selected closed at the ANTI-ICE control panel via the WING switch.
AIR CONDITIONING/PRESSURIZATION
Volume 2 Flight Crew Operating Manual Sep 13/2004
02-02-04 CSP 100-6 REV 1
BLEED AIR DISTRIBUTION (Cont)
APU BLEED VALVE
The APU bleed valve is controlled by the APU electrical control unit (ECU). The amount of bleed air taken from the APU
is controlled by the ECU sensing APU exhaust temperature. The APU bleed switch on the AIR COND/BLEED control
panel sends a signal to the ECU. The ECU determines when the APU is ready for bleed air loading and controls the opening,
closing, and modulation of the APU bleed valve.
When the APU bleed valve is open, APU bleed air is delivered to the right side of the bleed air manifold.
When the APU is shut down or there is a loss of signal from the ECU, the APU bleed valve moves to a fail-safe closed
position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Bombardier_Challenger_Global_00-Air_Cond_and_Press(3)