曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 Subtask 27-34-41-865-051
 F. Close Circuit Breakers
 (1) Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 21CE1, 21CE2, 21CE3, 22CE
 Subtask 27-34-41-720-050
 G. Test
 (1)
 Install the GAUGE-ELEVATOR NEUTRAL SETTING (98D27309006000) and verify the elevator neutral position, (Ref. TASK 27-34-00-820-003).

 (2)
 Do an operational test of the elevators (Ref. TASK 27-34-00-710-001).

 

 ELEVATOR - INSPECTION/CHECK
___________________________
 TASK 27-34-41-200-001
 Inspection/Check of the Elevator

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-34-41-000-001 Removal of the Elevator 27-34-41-400-001 Installation of the Elevator R CMM 552115PB601 27-34-41-991-005 Fig. 601
 3. Job Set-up
__________
 Subtask 27-34-41-010-051

 A. Get Access
 (1) Remove the aplicable elevator (Ref. TASK 27-34-41-000-001)
 4. Procedure
_________
 (Ref. Fig. 601/TASK 27-34-41-991-005)
 Subtask 27-34-41-220-050

 A. Fits and Clearances
 (1) Complete an inspection of these dimensions,

 Elevator Fits and Clearances
 Figure 601/TASK 27-34-41-991-005
 1EFF :  ALL  1  27-34-41 Page 602 
1  1  May 01/99
 1  1
 1CES  1

 

 -------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | B | 7.912 | 7.924 | | | 7.899 | | | | OD 3 |(0.3114) |(0.3119) | | |(0.3109) | | | | | | | 0.001 | 0.025 | | | 0.051 | | | | | (0.0000*| (0.0009*| | |(0.0020*| | B | 7.925 | 7.937 | | | | 7.950 | | | ID 1 |(0.3120) |(0.3124) | | | |(0.3129) | | ********** DIFFERENCE IN IN. MARKED BY A STAR IS TRUNCATED **********
 Subtask 27-34-41-220-051
 B. Fits and Clearances
 (1) Complete an inspection of these dimensions,
 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | B | 10.989 | 11.000 | | | 10.974 | | | | OD 1 |(0.4326) |(0.4330) | | |(0.4320) | | | | | | | 0.000 | 0.029 | | | 0.059 | | | | | (0.0000)| (0.0011)| | |(0.0023)| | B | 11.000 | 11.018 | | | | 11.033 | | | ID 2 |(0.4330) |(0.4337) | | | |(0.4343) | | -------------------------------------------------------------------------------
Subtask 27-34-41-220-052
 C. Fits and Clearances
 (1) Complete an inspection of these dimensions,

 -------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C | 15.989 | 16.000 | | | 15.974 | | | | OD 7 |(0.6294) |(0.6299) | | |(0.6288) | | | | | | | 0.000 | 0.029 | | | 0.059 | | | | | (0.0000)| (0.0011)| | |(0.0023)| | C | 16.000 | 16.018 | | | | 16.033 | | | ID 5 |(0.6299) |(0.6306) | | | |(0.6312) | | -------------------------------------------------------------------------------
Subtask 27-34-41-220-053
 D. Fits and Clearances
 (1) Complete an inspection of these dimensions,
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(54)