F 『
E C F M E
E E
E 56 E
E E
1 If the fault continues:
_
- disconnect the harness J5 from the ECU (4000KS),
- do a resistance check between: . pins 7 and 8 (>10 megohms) . pins 7 and 11 (>10 megohms) . pin 7 and the ground (>10 megohms).
a If there is an electrical short or a short to ground:
_
- replace the thrust reverser harness (Ref. AMM TASK 71-51-43-000-044) and (Ref. AMM TASK 71-51-43-400-044) or repair the aircraft wiring to the relay 14KS2 (Ref. ASM 73-25/16).
2 If nothing is found:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
R (2) If the test does not give the maintenance message J5, TR ACFT SW, R ECU:
- replace the RELAY-THRUST REV INHIBITION, ENG 2 (14KS2) on 188VU (Ref. ASM 73-25/16).
(a) If the fault continues:
- replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
(b) If the fault continues:
- replace the CTL UNIT-THROTTLE, ENG 2 (8KS2) (Ref. AMM TASK 76-11-19-000-042) and (Ref. AMM TASK 76-11-19-400-042).
(c) If the fault continues:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(d) If the fault continues:
R - do a check for a short to ground between (Ref. ASM 73-25/16): .the EIU2 (1KS2) pin AA/4C and the TCU2 (8KS2) pin E/C .the EIU2 (1KS2) pin AA/4A and the TCU1 (8KS2) pin E/C .the relay (14KS2) and its related wiring.
1 If nothing is found:
_
- replace the thrust reverser harness (Ref. AMM TASK 71-51-43-000-044) and (Ref. AMM TASK 71-51-43-400-044).
B. Do the test given in Para. 3.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 218
E E May 01/00 E E ECES
E TASK 71-50-00-810-807
F 『
E C F M E
E E
E 56 E
E E
Failure of the Thrust Reverser Inhibition Switch - Engine 1 - Channel B
1. Possible Causes
_______________
- CTL UNIT-THROTTLE, ENG 1 (8KS1)
- EIU-1 (1KS1)
- RELAY-THRUST REV INHIBITION, ENG 1 (14KS1)
- thrust reverser harness
- aircraft wiring
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 71-51-43-000-044 Removal of the Thrust Reverser (Channel A and B) Harness (4200KS) AMM 71-51-43-400-044 Installation of the Thrust Reverser (Channel A and B)
Harness (4200KS) AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) AMM 76-11-19-000-042 Removal of the Throttle Control Unit (8KS1, 8KS2) AMM 76-11-19-400-042 Installation of the Throttle Control Unit (8KS1,
8KS2) AMM 78-31-00-710-042 Operational Test of the Thrust Reverser System ASM 73-25/16 ASM 73-25/16 ASM 78-37/01
3. Fault Confirmation
__________________
A. Make sure that the throttle lever is not in the thrust reverser area.
B. Do the operational test of the thrust reverser system (Ref. AMM TASK 78-31-00-710-042).
F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 219
E E May 01/00 ERE
ECES E
F 『
E C F M E
E E
E 56 E
E E
4. Fault Isolation
_______________
A. This fault message is generated when the ECU detects an unwanted closure of the inhibition relay 14KS1 or a short or short to ground in the harness J6 or in the thrust reverser harness or in the aircraft wiring.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 動力裝置 POWER PLANT(14)
