PERMITTED TOTAL MAXIMUM CLEARANCE IN THIS JOINT 0.008 INCH.
Krueger Flaps Wear Limits
Figure 601 (Sheet 4)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-01
ALL ú ú 01 Page 605 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INDEX NO. PART NAME DIM. DESIGN LIMITS WEAR LIMITS REPLACE PART WORN REPAIR WORN PART REPAIR INSTR
DIAMETER PER-WEAR DIM. MITTED MAX CLEAR-ANCE DIA
MIN MAX
11 BUSHING ID 0.4370 0.4380 0.4410 1 0.0050 X
BUSHING OD 0.4350 0.4360 0.4310 X
2 12 BEARING ID 0.3745 0.3750 0.3795 0.0050 X
BOLT OD 0.3735 0.3745 0.3695 X
3 12 BEARING ID 0.2495 0.2500 0.2545 X
BOLT OD 0.2485 0.2495 0.2445 X
2 13 BUSHING ID 0.3745 0.3755 0.3795 0.0050 X
BOLT OD 0.3735 0.3745 0.3695 X
3 13 BUSHING ID 0.2495 0.2505 0.2545 0.0050 X
BOLT OD 0.2485 0.2495 0.2445 X
14 BEARING ID 0.2495 0.2505 0.2545 X
BOLT OD 0.2485 0.2495 0.2445 X
15 BUSHING ID 0.2495 0.2505 0.2545 X
BOLT OD 0.2485 0.2495 0.2445 X
16 BEARING ID 0.2495 0.2500 0.2545 0.0050 X
BOLT OD 0.2485 0.2495 0.2445 X
PERMITTED TOTAL MAXIMUM CLEARANCE IN JOINT 0.008 INCH. FLAPS NO. 11 AND 16 FLAPS NO. 12,13,14,15
Krueger Flaps Wear Limits
Figure 601 (Sheet 5)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-01
ALL ú ú 01 Page 606 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
VARIABLE CAMBER FLAPS - REMOVAL/INSTALLATION
____________________________________________
1. General_______
A. There are two tasks in this procedure. There is one task for the removal and one task for the installation of the variable camber flaps in the leading edge flap system. The procedure has these parts:
(1)
The installation of the safety locks
(2)
The removal of the folding nose
(3)
The removal of the variable camber flap
(4)
The installation of the linkage on the variable camber flap
(5)
The installation of the folding nose
(6)
The installation of the variable camber flap.
B.
The eleven outboard and midwing flaps in each wing are the variable camber flaps. The area of each flap is increased by a folding nose.
C.
The removal and installation procedure is the same for all the variable camber flaps.
D.
In this procedure the pivot points of the flap linkage are identified by the letters shown in Fig. 401. Each link is identified by the letter of its pivot points.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 7(82)
