(2)
AMM 29-11-00/201 Main Hydraulic Supply System

 (3)
AMM 32-00-30/201, Landing Gear Door Locks

 (4)
AIPC 32-32-14 Fig. 1

 (5)
AIPC 32-32-51 Fig. 2

 B.
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 C.
Prepare for Removal

 S 494-022
 WARNING:  YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1) Install the ground locks in all landing gear (AMM 09-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-14
 ALL  ú ú 01 Page 401 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 494-019
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Do this task: "Body Landing Gear Door Lock Installation" (AMM 32-00-30/201).

 S 494-018

 (3)  
Do this task: "Wing Landing Gear Door Lock Installation" (AMM 32-00-30/201).

 S 864-004

 (4)  
Remove the hydraulic pressure from system No. 4 (AMM 29-11-00/201).

 D.
Remove the Uplock Actuator.

 S 024-005
 (1)  
Remove the uplock actuator (1) (Fig. 401):

 (a)  
Disconnect the hydraulic lines (8 and 9) from the actuator (1).

 (b)  
Install caps on the hydraulic lines.

 (c)  
Remove the lower attach bolt (18) from the actuator rod end (1).

 (d)  
Remove the nut (6) from the hook pivot pin (14).

 (e)  
Remove the actuator (1) from the uplock assembly.

 (f)  
Remove the hydraulic fittings (2 and 10) from the actuator (1).

 (g)  
Install plugs in the ports of the hydraulic fittings.

 TASK 32-32-14-404-006
 3.  Wing Landing Gear Uplock Actuator Installation______________________________________________
 A. Consumable Materials
 (1)  
D00288 Lubricant - MCS 352 (Skydrol Assembly Lube)

 (2)  
D00196 Fluid - Hydraulic BMS 3-11, Type IV, Class 1

 (3)  
D00633 Grease - BMS 3-33 (preferred)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-14
 ALL  ú ú 01 Page 402 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
8.  HYDRAULIC TUBE  9.  HYDRAULIC TUBE 
7. WASHER  SEE  C  SEE  B 
2. ADAPTER 3. BACKUP RING 4. O-RING 5. COTTER PIN 6. NUT  13. WASHER 12. O-RING 11. BACKUP RING 10. ADAPTER  16. COTTER PIN 1. ACTUATOR A 
15. NUT 
1. ACTUATOR 
B 14.  UPLOCK ASSEMBLY HOOK PIVOT PIN  21. WASHER 20. WASHER 19. CLEVIS  17.  COUNTERSUNK WASHER 
18. BOLT 
C 
Figure 401 Wing Gear Uplock Actuator Installation 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-14
 ALL  ú ú 01 Page 403 ú Oct 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

RUBBER SLEEVE
(1/2 INCH ID X 1/8 INCH THK)

_______DO NOT USE THIS TOOL IF THE RUBBER SLEEVE IS DAMAGED.
CAUTION: IT CAN CAUSE DAMAGE TO THE UPLOCK DRIVE MECHANISM. EXAMINE THE SLEEVE FOR DAMAGE BEFORE AND AFTER USE. INSTALL A NEW SLEEVE IF IT IS DAMAGED.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(91)