曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

source. NOTE
5. If not precisely centered on the TADS reticle,
perform the following:
a. BRSIT TADS switch - TADS. Confirm
message, OUTFRONT BORESIGHT is
present.
b. BRSIT ENABLE switch - UP.
c. Adjust right and left thumbwheel controls
to center the target on the reticle.
d. BRSIT ENABLE switch - CENTER.
6. IAT switch - Off.
7. BRSIT TADS switch - OFF
d. TADS Manual Boresight Adjust.
NOTE
The manual boresight procedure is used
only to recapture or center the laser spot.
It is not an acceptable boresight procedure
for normal flight operations.
1.
2.
3.
BRSIT TADS switch - TADS. Confirm message
INTERNAL BORESIGHT is present.
LSR select switch - ON.
Sensor select switch - FLIR or TV as required.
4. FLIR PLRT pushbutton - Press to select
white hot.
5. Field-of-view select switch - N.
6. GAIN - Midrange (if using FLIR).
7. LVL - Fully counterclockwise (if using FLIR).
Ensure proper laser safety procedures
are followed.
If the laser spot is too weak or not visible,
perform Cue update.
9. Observe laser spot and optimize FLIR.
10. BRSIT ENABLE switch - UP for 1 second,
then move to center position. After 5 seconds,
the left and right thumbwheel controls will be
active; adjust laser spot in elevation and azimuth.
11. Laser trigger - Release.
12. LSR switch - OFF.
4.32 RAPID REARMING.
1. TAIL WHEEL switch - LOCK.
2. PARK BRAKE - Set.
3. HARS switch - NORM.
4. Weapons select switches - On.
5. PLT/GND ORIDE switch - ORIDE.
6. CPG ARM/SAFE switch - ARM.
7. ROCKETS control panel - Arm.
8. ANTI-COL switch - OFF.
9. Stray current check - Perform.
10. Weapons select switches - OFF
11. CPG ARM/SAFE switch - OFF
12. PLT/GND ORIDE switch - OFF.
13. Armament and pylon safety pins - Installed.
14. Rearming - Monitor.
15. ANTI-COL switch - As Desired.
16. Armament and pylon safety pins - Removed.
4-65
TM 1-1520-238-10
4.33 ARMAMENT INFLIGHT PROCEDURES.
4.33.1 30mm Gun System.
If 300 or more rounds have been fired
in the preceding ten minutes, and a
stoppage occurs, personnel must remain
clear of the aircraft for 30 minutes.
Aircraft crewmembers should
remain in the aircraft and continue
positive gun control.
1. CPG ARM/SAFE switches - ARM.
2. GUN select switch - As desired.
3. Crewmember desiring to fire - Establish
range to target and track target with selected
sight.
4. WAS switch - GUN.
5. Weapons trigger - Press, continue to fire as
required.
6. WAS - Deselect GUN.
4.33.2 AWS Harmonization Procedures
1. Locate target approximately 1000 meters
(± 50) from aircraft position.
2. Hover aircraft 100 FT (± 20) above target altitude
and maintain heading (± 5°) azimuth.
3. Sensor select switch - TV d.
4.
5.
6.
Field-of-view select switch - N or Z.
LSR select switch - ON. e.
Laser trigger - Press. Ensure the displayed
range to target is accurate to ± 10 meters.
7. Laser trigger - Press. Confirm range.
NOTE
Harmonization burst shall be accomplished
in the narrowest field of view
which the CPG can observe the rounds impact
(wide/narrow).
f.
g.
4-66 Change 4
8. Field-of-view select switch - W or N.
NOTE
A video recording may be used to verify
impact area.
9. Fire one or two 10 round bursts. Note centroid
of impact area.
10. Determine the appropriate sector from the appropriate
field of view Corrector Guides (figs
4-19.1 and 4-19.2) for harmonization offset
values.
NOTE
l A fraction of the offset values in a sector
can be used to improve accuracy
l Go to step 12 to enter modified
correctors.
11. For enter modified correctors:
a. DEK switch - SP1.
b. Enter G on the DEK.
C. The screen will display harmonization
corrector Deltas and Totals in the following
format:
AWS HARMONIZATION
DELTAS -MRAZ=+
00.0 EL=+00.0
TOTALS -MRAZ=+
00.0 EL=+00.0
On the DEK enter 1 to access azimuth or 2
to access elevation corrector value(s) to be
changed.
Enter corrector Delta value(s) from the
Corrector Guides (figs 4-19.1 and 4-19.2).
Repeat steps 1 through 11 while reducing
field of view as appropriate to DTV-NFOV
until center of impact is verified to be
within zoom FOV gates. When FOV gates
are achieved, proceed to step g.
DEK ENTER button - Press. This will
complete the modification.
TM 1-1520-238-10
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：阿帕奇攻擊直升機(jī)操作手冊2(17)