曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

console. 
11. On CDU press BOTH ARROWS soft key 
5. On KYK-13:.  twice. 
a. Mode switch -ON  12. Press PT/CT soft key. 
b. Fill switch -Place to .ll number (1-6) de- 13. Press RTN soft key. 
sired. 
14. Remove KYK-13 from .ll port. 
6. On CDU, INIT soft key -Press three times. 
LOAD KEY, then 1, then LOAD 1 will be displayed.  3.10.3 Normal Operation. 
7. On CDU, INIT soft key -Press again, to ini- 3.10.3.1 Change Mode. 
tiate load. LOAD KEYS will appear, then 
KEY 1(.ashing), and LOAD 1 with 1 .ashing  1. To access KY-100 control screen, COM .xed 
will appear. During load, 2 beeps will be heard  function key, then SK-6 soft key, then KY-100 
in the headsets. The key that was loaded is  soft key -Press. 
stored in .ll position 1. 
2. On the KY-100 control screen, PT/CT soft key 
8. On CDU, UP ARROW soft key -Press.  -Press, until either secure (CT) or clear voice 
LOAD 2 (.ashing) will be displayed.  (PT) appears in reverse video. 

3.10.3.2 Zeroize All Keys.
1. On the KY-100 control screen,  ZERO ALL soft key -Press. ZEROED will appear in the annunciator box, and a tone will be heard in the headset.

3.10.3.3 Zeroize Speci.c Keys.
1.
On the KY-100 control screen, OFFLINE soft key -Press.

2.  
UP ARROW,or RIGHT ARROW soft key -Press, until KEY OPS appears in the annuncia-tor box.

3.  
INIT KEY soft key -Press. LOAD KEY will be displayed in annunciator box.

4.  
UP ARROW,or RIGHT ARROW soft key -Press, until ZERO appears in the annunciator box.

5.  
INIT KEY soft key -Press. ZERO, with a .ashing number appears. The .ashing number indicates the currently selected key to be ze-roized.

6.  
UP ARROW,or RIGHT ARROW soft key -Press, until key location to zeroize is displayed.

7.  
INIT KEY soft key -Press. The entire ZERO N will now .ash.

8.  
INIT KEY soft key -Press again. The screen will blank while zeroizing process takes place. When zeroizing is complete, a tone will be heard in the headset, the display will brie.y change to ZEROED N, and then revert to ZERO N.

9.
Repeat steps 6 through 8 to zero other key po-sitions, as desired.

10.
When all desired key positions  are zeroized, PT/CT -Press.

 

3.11 EMERGENCY CONTROL PANEL (ECP).
The emergency control panel contains switches that control emergency functions of the AMS. It provides a means of communications in the event of avionics management sys-tem (AMS) dual control display unit (CDU) failure. The

AB0802
SA
Figure 3-16. Emergency Control Panel (ECP)
zeroize switch will erase all sensitive data in the AMS, regardless of the status of the CDUs.
3.11.1 Controls and Functions. All emergency con-trols for the AMS are located on the control panel, mounted in the lower console (Figure 3-16). The function of each control is as follows:
CONTROL/  FUNCTION 
INDICATOR 
ZEROIZE  Guarded  switch.  Placing  in 
switch  ZEROIZE  erases  all  COMSEC 
data from the system. 
CDU-1  AUTO  Designates bus controller 
CDU-2 switch 
AUTO  Normal position. Bus controller is 
designated  on  startup 
automatically. 
CDU-1  CDU- Manually designates either CDU 1 
2  or CDU 2 as bus controller. 
EMERG 
COMM switch 
NORM  Disables  AN/ARC-222  control 
panel. 
COMM  Activates  AN/ARC-222  control 
panel,  tunes  UHF  AN/ARC-164 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：UH-60Q 直升機技術手冊 直升機操作手冊 1(84)