曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(mix) transmission through the right pump assembly, filter,
cooler, jet protection screen, and to the jets which
spray the oil onto the various gears and bearings. One of
the scavenge elements of the right pump assembly returns
the oil from the No. 2 engine transmission sump
through a debris indicating screen and back to the No. 2
engine transmission oil reservoir. Engine transmissions
do not have auxiliary lubrication systems.
All No. 1 and No. 2 engine transmission lubrication system
components are on the combining (mix) transmission
except the jet protection screen and jets. Separate
oil jets are utilized for each transmission lubrication oil
system. The individual oil cooler for the combining (mix)
and both engine transmissions are mounted on the combining
(mix) transmission and utilize a common transmission
driven fan for cooling air.
2-7-6. Transmission Main Oil Pressure Indicator.
A transmission main oil pressure indicator is located on
the center instrument panel (fig. 2-7-1). It indicates either
the lowest main oil pressure in any one of the transmissions
or only the oil pressure in the transmission selected
by the pilot. The indicator is electrically connected to
each transmission. In addition, each transmission and
the aft rotor shaft bearing has a separate low pressure
switch. These switches are connected to the XMSN OIL
PRESS caution capsule on the master caution and the
TRANSMISSION MAIN OIL PRESS indicating lights on
the MAINTENANCE PANEL (fig. 2-10-1). Power to operate
the indicator is supplied by the No. 1 AC bus through
the XMSN OIL PRESS circuit breaker on the No. 1 PDP.
2-7-7. Transmission Main Oil Pressure Selector
Switch.
A transmission oil pressure selector switch is located on
the center instrument panel (fig. 2-7-1). The switch positions
are labeled TEST, SCAN, FWD, AFT, MIX, LEFT,
and RT. When the switch is set to TEST, the pointer on
the transmission pressure indicator will drop to zero or
below. When the switch is set to SCAN, the lowest main
oil pressure among all the transmission will be indicated.
The remaining positions are used to select a particular
transmission oil pressure indication. When selecting a
particular switch position, be sure the switch is in detent.
If the switch is not in detent, the pressure gage will indicate
zero.
2-7-8. Transmission Main Oil Temperature Indicator.
A transmission oil temperature indicator is located on the
center instrument panel (fig. 2-7-2). It reads from –70
to
+150
C. It indicates the highest oil temperature among
all the transmissions or only the oil temperature of the
selected transmission. A temperature probe is located in
the forward and aft transmission sumps and in each
compartment of a three-compartment oil tank for the
combining (mix) transmission and in each engine transmission.
The temperature probes in the three tank
compartments measure oil temperature in the tank and
may not immediately indicate a transmission problem.
Loss of oil or low oil pressure may not be accompanied
by high oil temperature indication.
Figure 2-7-1. Transmission Main Oil Pressure
Indicator and Selector Switch
Each temperature probe incorporates a high oil temperature
switch which is independent of the temperature indicator
and is triggered at 140
C, lighting the XMSN OIL
HOT caution capsule on the master caution panel and to
the TRANSMISSION OVERTEMP magnetic indicator on
the MAINTENANCE PANEL. Power to operate the indicator
is supplied by the No. 1 AC bus through the XMSN
OIL TEMP circuit breaker on the No. 1 PDP.
2-7-9. Transmission Main Oil Temperature Selector
Switch
A transmission oil temperature selector switch is on the
center panel below the transmission oil temperature indicator
(fig. 2-7-2). The switch positions are labeled TEST,
SCAN, FWD, AFT, MIX, LEFT, and RT. When the switch
is set to TEST, the pointer on the transmission oil temperature
indicator deflects full scale toward low temperature.
.When the switch is set to SCAN, the highest oil temperaTM
1-1520-240-10
2-7-3
ture among all transmissions is indicated. The remaining
positions are used for selecting a particular transmission
fied by the oil temperature selector switch oil temperature
indication. When selecting a particular switch position,
be sure the switch is in detent. If the switch is not detent,
the oil temperature indicator will indicate –70
C.
Figure 2-7-2. Transmission Main Oil Temperature
Switch and Indicator
2-7-10. Transmission Oil Cautions.
Five transmission oil caution capsules are on the master
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：支奴干運輸直升機操作手冊1(40)