曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

5. LOAD key Initiates loading of selected data.
6. ALL key Selects data for loading. Individual lines may be deselected using
line address keys.
7. WAYPOINTS key Selects/deselects WPT and TGT data for loading.
8. COMM key Selects/deselects communication data for loading.
9. INIT POS key Selects/deselects initial position coordinates for loading.
Figure 4-23. LOAD MISSION 2 Page
4-50
TM 1-1520-248-10
CONTROL/INDICATOR FUNCTION
1. (CDS2) ATHS key Selects/deselects ATHS data for storage.
IDM key Selects/deselects IDM data for storage.
2. LASER CODES key Selects/deselects laser data for storage.
3. WEAPONS DATA key Selects/deselects WEAPONS data for storage.
4. DATA LOADER TRANSFER key Selects DATA LOADER TRANSFER page.
5. STORE ID key Allows the mission identifier to be input. Only displays in the store
mission mode.
6. STORE key Initiates storage of selected data.
7. ALL key Selects all data for storage.
8. WAYPOINTS key Selects/deselects WPT data for storage.
9. COMM key Selects/deselects communication data for storage.
10. INIT POS key Selects/deselects initial position coordinates for storage.
Figure 4-24. STORE MISSION 2 Page
4-51
TM 1-1520-248-10
CONTROL/INDICATOR FUNCTION
1. GOTO PAGE key Selects NOTEBOOK page identified by entered number.
2. INS LINE key Inserts line of text into text field.
3. DEL LINE key Deletes line of text from text field.
NOTE
The legend PREV PAGE is not displayed on page 1.
4. PREV PAGE key Accesses previous NOTEBOOK page.
5. NEXT PAGE key Accesses next NOTEBOOK page.
6. → key Moves cursor right.
7. ← key Moves cursor left.
8. ∇ key Moves edit bar down text field.
9. Δ key Moves edit bar up text field.
10. EDIT key Activates cursor bar for editing.
Figure 4-25. (CDS2) NOTEBOOK Page
4-52
TM 1-1520-248-10
increases display brightness through eight
NOTE settings. R-2 decreases display brightness
and turns ODA off. Function is the same for
CPG ODA display brightness can be p i l o t ODA when INITIAL PAGE 2 is
controlled from INITIAL PAGE 2 with R-1 accessed from pilot MFD.
and R-2 keys. R-1 turns on ODA and
6. Press ODA switch to select ODA display
brightness as desired.
NOTE
Pilot and CPG processing are independent
of each other, except that only the pilot has
control of Hover Bob-Up mode. (See fig. 4-
29.)
7. ADSS DECLUTTER key  Press to select no
declutter level, level 1 declutter, or level 2
declutter, as desired.
a. Level 1 declutter removes analog radar
altitude, rate of climb, and analog scale.
b. Level 2 declutter also removes the
barometric altitude, indicated airspeed,
torque and torque box, Hover Bob-up
position box, and all weapon symbology.
8. (CDS4) Weapon Symbology  Weapon
symbology from the MFD is also displayed on
the ODA (fig. 4-28). This symbology is
406075-602
J1145
removed at level 2 declutter.
Figure 4-26. ADSS ODA Test Pattern
4-53
TM 1-1520-248-10
CONTROL/INDICATOR FUNCTION
1. Bearing to waypoint pointer Indicates bearing to navigational waypoint.
2. Magnetic heading tape Displays magnetic heading 90° left and right of the helicopter
centerline.
3. MMS bearing indicator Indicates line-of-sight bearing of the mast mounted sight.
4. Barometric altimeter Displays barometric altitude, MSL, of the helicopter in increments of
10 feet.
5. Acceleration cue Shows rate of acceleration.
6. Vertical speed indicator Indicates rate of climb or descent with middle scale line representing
0, and maximum deflection either above or below zero represents a
rate of 1000 feet per minute.
Figure 4-27. ADSS ODA Hover and Hover Bob-Up Display (Sheet 1 of 2)
4-54
TM 1-1520-248-10
(Cont)
CONTROL/INDICATOR FUNCTION
7. HI indicator Flashes when maximum value input is exceeded. Refer to Chapter 3
for setting input values.
8. Radar altimeter readout Displays the digital readout of altitude (AGL) in 1-foot increments up
to 200 feet and 5-foot increments to 1500 feet.
9. LO indicator Flashes when aircraft drops below minimum value input. Refer to
Chapter 3 for setting input values.
10. Radar altimeter scale Vertical scale readout of altitude (AGL) from 0 to 200 feet.
11. Mast torque indicator Displays digital readout of mast torque. Indication will be boxed
when the mast torque is equal to or greater than 100%.
12. DEGRADED Displays when NAV mode is not in GPS/INS or NAV FOM > 1.
(bob-up mode only)
13. Turn and slip Indicates trim and turn rate.
14. Caution bar Displays and flashes below turn and slip indicator when caution
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：TECHNICAL MANUAL OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPT(107)