Applicable to: ALL
GENERAL
The preparation for descent and approach consists of :
‐ Entering PERF and WIND data
‐ Defining the lateral and vertical F-PLN
‐ Checking the tuning (auto or manual) of the appropriate navaids
After receiving the arrival information, the pilot should use the following procedure.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A330/A340 FLEET PRO-NOR-SRP-01-50 P 8/14
FCOM 19 AUG 10
REVISION OF LATERAL F-PLN
PERFORM a lateral revision at destination
SELECT an ARRIVAL
SELECT an APPROACH, a STAR, a TRANSITION, a VIA.
When the pilot selects successive items, the page are automatically sequenced. But pressing the
[→] key brings up the APPR and STAR page successively.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A330/A340 FLEET PRO-NOR-SRP-01-50 P 9/14
FCOM 19 AUG 10
CHECK the temporary revision including the missed approach.
INSERT the temporary revision, [6R] key.
REVISION OF VERTICAL FLIGHT PLAN
CHECK the speed and altitude constraints as displayed on the ND. (Use the CSTR pusbutton).
ENTER any additional speed or altitude constraints using the vertical revision page.
In order not to be too fast when commencing approach, you may insert a speed constraint at the
FAF (Final Approach Fix).
When all computations are completed :
REVIEW the flight plan using the approach chart.
When the destination runway changes and if the previously selected STAR is compatible with the
new runway, the system selects it automatically in the temporary F-PLN. If the pilot has entered
any revision or constraint on this STAR, it will not be transferred. The pilot must reenter it in order
to retain it for this approach.
ENTERING THE WINDS FOR DESCENT
Refer to DSC-22_20-30-20-20-B WIND - TEMPERATURE - QNH - GENERAL.
PRESELECTING A MANAGED SPEED/MACH
As long as the descent phase is not active, the PERF DES page may either be used to select a
speed, or a Mach number, or both, to replace the optimum descent speed.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A330/A340 FLEET PRO-NOR-SRP-01-50 P 10/14
FCOM 19 AUG 10
The Flight Guidance Computer then uses the entered speed, instead of the optimum speed for
computing the descent profile.
When the system switches to the descent phase, it sets the MANAGED target speed to the
entered speed. From there, the speed may only be modified by using the FCU selector knob.
Once in descent phase, the pilot cannot modify the MANAGED speed again.
PROCEDURE
PRESS ‐ the PERF key on the MCDU.
‐ SELECT the “NEXT PHASE” prompt.
‐ WRITE the descent speed into the scratchpad and ENTER it.
The 3L field displays the imposed managed speed value.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A330/A340 FLEET PRO-NOR-SRP-01-50 P 11/14
FCOM 19 AUG 10
MODIFICATION OF THE CABIN RATE
PROCEDURE
PRESS the PERF key on MCDU
WRITE the new cabin rate into the scratchpad
ENTER it in the [ 4R ] field.
ENTERING THE APPROACH DATA
From PERF DES page, SELECT “NEXT PHASE” [ 6R ] key to display the APPR page.
ENTER QNH, TEMP, WIND at destination (magnetic or true North reference depending on the
airport’s reference). MDA/MDH or DH
(The PFD displays the MDA/MDH or DH only when the distance to destination is less than
250 nm).
CHECK and, if necessary, MODIFY
• LDG CONF (landing configuration)
• Vapp (the FM-computed value may be modified)
• TRANS ALT (transition altitude)
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A330/A340 FLEET PRO-NOR-SRP-01-50 P 12/14
FCOM 19 AUG 10
The scratchpad displays “ENTER DEST DATA” if the approach page is not completed when the
aircraft is 180 nm from destination.
SELECT “NEXT PHASE” in order to display the GO AROUND page.
CHECK and, if necessary, MODIFY the THR RED ALT and ACC ALT.
SELECTING THE RADIO NAVAIDS
CHECK, or SELECT, the appropriate NAVAIDS for the approach.
For an ILS procedure, the ILS will be autotuned.
NDBs must be entered manually.
Note: When the destination has a VOR/DME, enter it manually in the VOR field. Enter
its identifier in the BRG/DIST field of the PROG page. This allows you to perform a
permanent NAV accuracy check.
A330/A340 FLIGHT CREW
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A330/A340機組操作手冊 FLIGHT CREW OPERATING MANUAL FCOM 10