曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

FILL Port Access connector.
NOTE
The fill cable for the KYK-13 may be used
while loading MWOD information into the
radio, but is not required.
4. KYK-13 - Set mode switch to OFF/CHECK.
5. KYK-13 -Install on FILL Port Access connector.
6. KYK-13 - Set mode switch to ON.
7. STATUS button - Press; ensure the frequency/
status LCD displays FILL.
8. KYK-13 - Set address switch to applicable
channel (1 through 6).
3-18.10 Change 3
9. LOAD button -Press for two seconds. Listen
for a series of beeps and confirm frequency/
status indicator displays WOD OK. If frequency/
status indicator displays BAD, the
KYK-13 must be reloaded prior to repeating
steps 4 through 9.
NOTE
The CHAN indicator steps down from
memory location 20 to 14, then displays 01
while the KYK-13 is connected and
turned on. This allows entry of the operational
date information if required.
10. KYK-13 - Set to next applicable channel and
repeat step 9. Observe that WOD OK is displayed
on the frequency/status indicator after
each WOD is loaded.
NOTE
If operational date is desired, proceed to
step 11; if not desired, proceed to step 12.
11. STATUS button - Depress, if operational date
entry is desired. Set date on frequency
switches in XAB.XXX format. Toggle TTONE
switch to TONE position and release.
12. KYK-13 - Set mode switch to OFF/CHECK
and remove KYK-13.
13. Preset Frequency Label Cover - Close.
The radio will return to its’ previous mode prior to loading
and both displays will return to the previous settings.
3.7B.8 Verifying MWOD is Loaded.
1. STATUS button - Press; ensure the frequency/
status LCD displays VER/OP.
2. Function Selector switch - Set to MNL.
3. Frequency switches - Set to the day of the
month to be verified. Code format is
XAB.XXX, where A and B are the day of the
month of the Date Tag associated with the
WOD to check.
4. CHAN switch - Set to Channel 20. Switch
momentarily to channel 19 and return to
channel 20. A single beep verifies the MWOD
with a matching day of the month code stored
in memory. If a single beep is not heard, the
code is not stored in memory. Repeat steps 3
and 4 to check other days of the month.
TM 1-1520-238-10
3.7B.9 MWOD Erase. NOTE
1.
2.
3.
4.
5. Function Selector switch - MNL. 2.
6. T-TONE switch - Toggle to TONE and release.
MWODs should now be erased.
7. Function Selector switch - PRESET.
8. Frequency switches - Set to 220.000.
9. LOAD button - Lift preset frequency label
cover and push LOAD button. Close cover.
The radio is now in the Verify/Operate mode/
3.7B.10 Alternate MWOD Erase.
1. Preset Frequency Label Cover - Open to reveal
ZERO switch.
CHAN switch - Set to channel 20.
Function Selector switch - PRESET.
Frequency switches - Set to 220.050.
LOAD button - Lift preset frequency label
cover and push LOAD button.
2. ZERO switch - Rotate counterclockwise, then
return to normal position. ERASE should be
displayed on the frequency/status indicator.
All MWODs are now erased.
3.7B.11 Receiving Time of Day (TOD) and TOD Update
m.
NOTE
A steady warning tone will be heard when
the anti-jamming mode is selected and
the TOD or a valid WOD has not been entered.
A pulsating tone will be heard if an
invalid net is selected.
1. Function Selector switch - PRESET or MNL.
2. T-TONE switch - Toggle to T and release.
3. TOD - Request from another station.
If TOD is being automatically beaconed
from another station, the first TOD message
received within one minute of selected
T position will be accepted.
a. TOD Send.
1.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Function Selector switch - PRESET or MNL.
Rotate frequency switches or CHAN switch to
a predesignated frequency for TOD transmission.
T-TONE switch - Toggle to TONE position
for two seconds and release.
Loading Operational Date.
CHAN switch - Set to Channel 20.
Function Selector switch - PRESET.
Frequency switches - Set to 220.025.
LOAD button - Lift preset frequency label
cover and push LOAD button.
CHAN switch - Set to Channel 01.
Frequency switches - Set to the operational
date in the format of XAB.XXX, where A and
B are the day of the month of the Date Tag. X
can be any value.
T-TONE switch - Toggle to TONE and release.
Listen for a wavering tone.
Function Selector switch - PRESET.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：阿帕奇攻擊直升機操作手冊1(72)