曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

• Failure detection system (CAA aircraft only)
2. Description of Subsystems, Units and Components:
A. Control Column System:
(See Figure 7.)
The pilot’s and copilot’s control columns mount to a common transverse
torque tube supported by a bearing on each end. Moving the control
column fore and aft rotates the torque tube that, in turn, transmits the
inputs rearward through conventional mechanical linkage. Adjustable stops
on the torque tube limit control column movement to eight inches aft and
five inches forward of the neutral position.
An eddy current damper is connected to the bottom of the control column
OPERATING MANUAL
PRODUCTION AIRCRAFT SYSTEMS 2A-27-00
Page 7
October 11/02
Revision 8
output crank. The damper is designed to sense control column movement
and provide a counteracting damping force or artificial feel. Damping force
is generated in proportion to control column velocity. Should the eddy
current damper jam or fail, its internal clutch releases to allow control
column movement.
B. Mechanical Actuation System:
(See Figure 3.)
Control column inputs are transmitted rearward through a system of pushpull
rods, bellcranks, cables and a sector assembly to an input cable sector
below the base of the vertical stabilizer in the tail compartment. Connected
to the input cable sector are the elevator actuator, autopilot servo and
stability springs. Final output of the sector is to the elevator actuator input
lever.
Movement of the actuator input lever displaces the elevator actuator’s
servo control valve, directing Combined and Flight hydraulic system
pressure to the actuator cylinders. When under pressure, the actuator body
moves while the its piston remains motionless. Movement of the actuator
body in turn moves its output crank. Output crank movement is transmitted
upward and aft to the left and right elevators through a system of push-pull
rods and cranks, resulting in the desired elevator deflection.
Stability springs, commonly referred to as down springs, provide
approximately 13 pounds of pull on the control columns. This pulling force
keeps pilot feel forces out of the friction band at low airspeeds.
C. Hydraulic Boost System:
The elevator actuator is a dual tandem actuator consisting of two pistons
secured to a common shaft. The pistons move inside a common cylinder
divided to create two separate cylinders. One cylinder receives Flight
hydraulic system pressure while the other cylinder receives Combined
hydraulic system pressure.
Mechanical movement of the actuator input lever moves the servo control
valve from its neutral position. The servo control valve then directs
hydraulic pressure to one of the actuator’s two cylinders and connects
each cylinder’s opposite side to return. When the elevator reaches the
desired deflection, the servo control valve shifts to its neutral position to
lock hydraulic pressure within the actuator, in effect preventing further
surface movement.
The elevator actuator also has an internal hydraulic damper that provides
damping force proportional to the square of its input velocity. This damping
action ensures operational stability for the elevators when hydraulically
boosted whereby a portion of the actuator’s output is fed back to the input
system.
D. Manual Reversion System:
During normal flight operations, the Combined and Flight hydraulic
systems each supply and maintain 3000 psi to the elevator actuator. Loss
of system pressure due to a single system failure has no effect on
operation of the pitch flight control system.
Loss of system pressure from both hydraulic systems will automatically
revert the pitch flight control system to manual control. As pressure at the
OPERATING MANUAL
2A-27-00 PRODUCTION AIRCRAFT SYSTEMS
Page 8
October 11/02
Revision 8
actuator drops below 60 psi, bypass valves within the actuator open to
allow the actuator piston to idle. With the actuator piston idling, the system
is said to be in manual reversion, technically explained in the following
paragraph.
The actuator input crank and output crank rotate on a common pivot point.
They are linked by a pin and elongated slot arrangement. The input crank
is on the pin and the output crank is on the slot. With the actuator piston
idling, the pin moves within the slot until it reaches either end. At this point,
mechanical contact is made and the input crank now drives the output
crank. The output crank in turn drives the left and right elevators through its
push-pull rods and cranks.
Manual reversion of the pitch flight control system is also possible by
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：灣流4操作手冊 Gulfstream IV Operating Manual 2(8)