曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

mass of air to a much slower velocity.
As stated in Chapter 14, both piston and gas turbine
engines are internal combustion engines and have a
similar basic cycle of operation; that is, induction,
compression, combustion, expansion, and exhaust. Air
is taken in and compressed, and fuel is injected and
burned. The hot gases then expand and supply a
surplus of power over that required for compression,
and are finally exhausted. In both piston and jet
engines, the efficiency of the cycle is improved by
increasing the volume of air taken in and the
compression ratio.
Part of the expansion of the burned gases takes place in
the turbine section of the jet engine providing the
necessary power to drive the compressor, while the
remainder of the expansion takes place in the nozzle of
the tail pipe in order to accelerate the gas to a high
velocity jet thereby producing thrust. [Figure 15-1]
In theory, the jet engine is simpler and more directly
converts thermal energy (the burning and expansion of
gases) into mechanical energy (thrust). The piston or
reciprocating engine, with all of its moving parts, must
convert the thermal energy into mechanical energy and
then finally into thrust by rotating a propeller.
One of the advantages of the jet engine over the piston
engine is the jet engine’s capability of producing much
greater amounts of thrust horsepower at the high
altitudes and high speeds. In fact, turbojet engine
efficiency increases with altitude and speed.
Direction of Flight
Air
Enters
Inlet
Duct Exhaust
Combustion
Drive Shaft
Six-Stage Compressor
TURBOJET ENGINE
Two-Stage
Turbine
Figure 15-1. Basic turbojet engine.
Ch 15.qxd 5/7/04 10:22 AM Page 15-1
15-2
Although the propeller driven airplane is not nearly as
efficient as the jet, particularly at the higher altitudes
and cruising speeds required in modern aviation, one
of the few advantages the propeller driven airplane has
over the jet is that maximum thrust is available almost
at the start of the takeoff roll. Initial thrust output of the
jet engine on takeoff is relatively lower and does not
reach peak efficiency until the higher speeds. The fanjet
or turbofan engine was developed to help compensate
for this problem and is, in effect, a compromise
between the pure jet engine (turbojet) and the propeller
engine.
Like other gas turbine engines, the heart of the turbofan
engine is the gas generator—the part of the engine
that produces the hot, high-velocity gases. Similar to
turboprops, turbofans have a low pressure turbine section
that uses most of the energy produced by the gas
generator. The low pressure turbine is mounted on a
concentric shaft that passes through the hollow shaft of
the gas generator, connecting it to a ducted fan at the
front of the engine. [Figure 15-2]
Air enters the engine, passes through the fan, and splits
into two separate paths. Some of it flows around—
bypasses—the engine core, hence its name, bypass
air. The air drawn into the engine for the gas generator
is the core airflow. The amount of air that bypasses
the core compared to the amount drawn into the gas
generator determines a turbofan’s bypass ratio.
Turbofans efficiently convert fuel into thrust because
they produce low pressure energy spread over a large
fan disk area. While a turbojet engine uses all of the
gas generator’s output to produce thrust in the form of
a high-velocity exhaust gas jet, cool, low-velocity
bypass air produces between 30 percent and 70 percent
of the thrust produced by a turbofan engine.
The fan-jet concept increases the total thrust of the jet
engine, particularly at the lower speeds and altitudes.
Although efficiency at the higher altitudes is lost (turbofan
engines are subject to a large lapse in thrust with
increasing altitude), the turbofan engine increases
acceleration, decreases the takeoff roll, improves initial
climb performance, and often has the effect of
decreasing specific fuel consumption.
OPERATING THE JET ENGINE
In a jet engine, thrust is determined by the amount of
fuel injected into the combustion chamber. The power
controls on most turbojet and turbofan powered airplanes
consist of just one thrust lever for each engine,
because most engine control functions are automatic.
The thrust lever is linked to a fuel control and/or electronic
engine computer that meters fuel flow based
upon r.p.m., internal temperatures, ambient conditions,
and other factors. [Figure 15-3]
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：AIRPLANE FLYING HANDBOOK 飛機飛行手冊下(68)