曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

plane measured in degrees from north.
b. The ILS localizer signal pattern usually specified
as the front course or the back course.
Pilot/Controller Glossary 8/5/04
PCG C−8
c. The intended track along a straight, curved, or
segmented MLS path.
(See BEARING.)
(See INSTRUMENT LANDING SYSTEM.)
(See MICROWAVE LANDING SYSTEM.)
(See RADIAL.)
CPDLC−
(See CONTROLLER PILOT DATA LINK
COMMUNICATIONS.)
CPL [ICAO]−
(See ICAO term CURRENT FLIGHT PLAN.)
CRITICAL ENGINE− The engine which, upon
failure, would most adversely affect the performance
or handling qualities of an aircraft.
CROSS (FIX) AT (ALTITUDE)− Used by ATC
when a specific altitude restriction at a specified fix
is required.
CROSS (FIX) AT OR ABOVE (ALTITUDE)− Used
by ATC when an altitude restriction at a specified fix
is required. It does not prohibit the aircraft from
crossing the fix at a higher altitude than specified;
however, the higher altitude may not be one that will
violate a succeeding altitude restriction or altitude
assignment.
(See ALTITUDE RESTRICTION.)
(Refer to AIM.)
CROSS (FIX) AT OR BELOW (ALTITUDE)−
Used by ATC when a maximum crossing altitude at
a specific fix is required. It does not prohibit the
aircraft from crossing the fix at a lower altitude;
however, it must be at or above the minimum IFR
altitude.
(See ALTITUDE RESTRICTION.)
(See MINIMUM IFR ALTITUDES.)
(Refer to 14 CFR Part 91.)
CROSSWIND−
a. When used concerning the traffic pattern, the
word means “crosswind leg.”
(See TRAFFIC PATTERN.)
b. When used concerning wind conditions, the
word means a wind not parallel to the runway or the
path of an aircraft.
(See CROSSWIND COMPONENT.)
CROSSWIND COMPONENT− The wind component
measured in knots at 90 degrees to the longitudinal
axis of the runway.
CRUISE− Used in an ATC clearance to authorize a
pilot to conduct flight at any altitude from the
minimum IFR altitude up to and including the
altitude specified in the clearance. The pilot may
level off at any intermediate altitude within this block
of airspace. Climb/descent within the block is to be
made at the discretion of the pilot. However, once the
pilot starts descent and verbally reports leaving an
altitude in the block, he/she may not return to that
altitude without additional ATC clearance. Further, it
is approval for the pilot to proceed to and make an
approach at destination airport and can be used in
conjunction with:
a. An airport clearance limit at locations with a
standard/special instrument approach procedure. The
CFRs require that if an instrument letdown to an
airport is necessary, the pilot shall make the letdown
in accordance with a standard/special instrument
approach procedure for that airport, or
b. An airport clearance limit at locations that are
within/below/outside controlled airspace and without
a standard/special instrument approach procedure.
Such a clearance is NOT AUTHORIZATION
for the pilot to descend under IFR conditions below
the applicable minimum IFR altitude nor does it
imply that ATC is exercising control over aircraft in
Class G airspace; however, it provides a means for the
aircraft to proceed to destination airport, descend, and
land in accordance with applicable CFRs governing
VFR flight operations. Also, this provides search and
rescue protection until such time as the IFR flight
plan is closed.
(See INSTRUMENT APPROACH
PROCEDURE.)
CRUISE CLIMB− A climb technique employed by
aircraft, usually at a constant power setting, resulting
in an increase of altitude as the aircraft weight
decreases.
CRUISING ALTITUDE− An altitude or flight level
maintained during en route level flight. This is a
constant altitude and should not be confused with a
cruise clearance.
(See ALTITUDE.)
(See ICAO term CRUISING LEVEL.)
CRUISING LEVEL−
(See CRUISING ALTITUDE.)
CRUISING LEVEL [ICAO]− A level maintained
during a significant portion of a flight.
8/5/04 Pilot/Controller Glossary
PCG C−9
CT MESSAGE− An EDCT time generated by the
ATCSCC to regulate traffic at arrival airports.
Normally, a CT message is automatically transferred
from the Traffic Management System computer to the
NAS en route computer and appears as an EDCT. In
the event of a communication failure between the
TMS and the NAS, the CT message can be manually
entered by the TMC at the en route facility.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空信息手冊縮寫詞(24)