曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

is the total air inlet temperature detected by the T12 engine
sensors.
The ACT CH A shows the active channel or the channel that
controls the engine. The GMM CH A shows the ground
maintenance mode (GMM) channel or the channel that
controls CDU BITE.
T25 SELECTION
The T25 SELECTION page shows T25 values for channels A and
B. SEL T25 is the temperature the EEC uses to control the
engine.
The ACT CH A shows the active channel or the channel that
controls the engine. The GMM CH A shows the ground
maintenance mode (GMM) channel or the channel that
controls CDU BITE.
T3 SELECTION
The T3 SELECTION page shows T3 values for channels A and
B. SEL T3 is the temperature the EEC uses to control the
engine.
The ACT CH A shows the active channel or the channel that
controls the engine. The GMM CH A shows the ground
maintenance mode (GMM) channel or the channel that
controls CDU BITE.
TCC SELECTION
The TCC SELECTION page shows TCC values for channels A
and B. SEL TCC is the temperature the EEC uses to control the
engine.
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 10
EFFECTIVITY
GUN ALL 73-21-00
Page 98.51
D633A101-GUN Oct 10/2005
BOEING PROPRIETARY - Copyright#- Unpublished Work - See title page for details.
CFM56 ENGINES (CFM56-7) 737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL
73-21-00-251
The ACT CH A shows the active channel or the channel that
controls the engine. The GMM CH A shows the ground
maintenance mode (GMM) channel or the channel that
controls CDU BITE.
T495 SELECTION
The T495 SELECTION shows T495 values for channels A and B.
SEL T495 is the temperature the EEC uses to control the engine.
The ACT CH A shows the active channel or the channel that
controls the engine. The GMM CH A shows the ground
maintenance mode (GMM) channel or the channel that
controls CDU BITE.
Training Information Point
If a parameter is not available, (?) symbols show for the
parameter. If the parameter is out of range, (-) symbols show for
the parameter.
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 10
EFFECTIVITY
GUN ALL 73-21-00
Page 98.52
D633A101-GUN Oct 10/2005
BOEING PROPRIETARY - Copyright#- Unpublished Work - See title page for details.
CFM56 ENGINES (CFM56-7) 737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL
73-21-00-251
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 10
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 10
EFFECTIVITY
GUN ALL 73-21-00
Page 98.53
D633A101-GUN Oct 10/2005
BOEING PROPRIETARY - Copyright#- Unpublished Work - See title page for details.
CFM56 ENGINES (CFM56-7) 737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL
73-21-00-251
General
These are additional CDU screens for CONTROL TEMPS.
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 11
EFFECTIVITY
GUN ALL 73-21-00
Page 98.54
D633A101-GUN Oct 10/2005
BOEING PROPRIETARY - Copyright#- Unpublished Work - See title page for details.
CFM56 ENGINES (CFM56-7) 737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL
73-21-00-253
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 11
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 11
EFFECTIVITY
GUN ALL 73-21-00
Page 98.55
D633A101-GUN Oct 10/2005
BOEING PROPRIETARY - Copyright#- Unpublished Work - See title page for details.
CFM56 ENGINES (CFM56-7) 737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL
73-21-00-253
General
The FUEL SYSTEM input monitoring page lets you monitor
these fuel system parameters:
* FUEL FLOW in pounds per hour
* FMV POS (flow metering valve position)
* FILTER BYPASSED.
FUEL FILTER
The FUEL FILTER page gives you the fuel filter bypass switch
positions for EEC channels A and B. FILTER BYPASSED shows
the fuel filter bypass position the EEC sends to the DEUs.
The ACT CH A shows the active channel or the channel that
controls the engine. The GMM CH A shows the ground
maintenance mode (GMM) channel or the channel that
controls CDU BITE.
Training Information Point
If a parameter is not available, (?) symbols are put in place of
the parameter. If the parameter is out of range, (-) symbols are
put in place of the parameter.
ENGINE FUEL AND CONTROL - ENGINE CONTROL - TRAINING INFORMATION POINT - EEC BITE - INPUT PG 11
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：ENGINE FUEL AND CONTROLS(41)