曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

DH (Decision Height) – The DH button allows entry and arming of
altitude alerting at a set decision height. To set a DH, first enter the
data (DTA) entry (ENT) mode, press the DH button, and rotate the
selector knob to input the desired decision height to the nearest 100
feet above the specified decision height. For example, for a DH of
1160 feet set 1.2 (1200 feet). After setting the desired decision height,
press the DTA button again to accept the entered DH. The display will
show the selected DH for approximately 5 seconds and then revert to
Alt mode until the selected DH is reached during descent. The DH
annunciator will remain illuminated indicating a decision height is set.
As the airplane approaches within approximately 50 feet of the
decision height, the alert will sound and the DH light will flash. As the
airplane passes through approximately 50 feet beyond the decision
height, the alert will sound and the light will flash again. Pressing the
DH button again will disable the DH function causing the DH
annunciation to go out. Repeated activation of the DH button
alternately activates and deactivates the DH mode.
VS (Vertical Speed) – At initial start up, after self-test, pressing the
Altitude Selector / Alerter VS button enables vertical speed selector
mode. The initial vertical speed will be set at + 2 indicating a climb at
200 feet per minute. Rotating the selector input knob will change the
selected vertical speed in 100 FPM increments. Rotate CW to
increase vertical speed or CCW to Decrease vertical speed. The
maximum vertical speed is ± 1600 FPM (± 16). Zero vertical speed is
not selectable.
The vertical speed display is the only Altitude Selector / Alerter
function available in the ‘operate’ mode. Therefore, vertical speed
changes can be commanded by rotating the selector input knob.
Vertical speeds can also be entered in the data (DTA) entry (ENT)
mode by pressing the VS button and using the selector input knob to
enter a new vertical speed. The DTA button must be pressed again to
accept the new vertical speed and enter the ‘operate’ mode.
The Altitude Selector / Alerter VS mode can be disabled by pressing
the Altitude Selector / Alerter MAN button.
MAN (Manual) – Vertical Speed selection can be completely
decoupled from the autopilot system by depressing the Altitude
Selector / Alerter MAN button.
Revision 04: 08-15-07
P/N 11934-S27 1 of 16
Cirrus Design Section 9
SR20 Supplements
Pilot’s Operating Handbook and
FAA Approved Airplane Flight Manual
Supplement
For
S-Tec System 55SR Autopilot
When the S-Tec System Fifty Five SR (55SR) Autopilot is installed in
the Cirrus Design SR20, serials 1337 and subsequent, this
Supplement is applicable and must be inserted in the Supplements
Section (Section 9) of the Cirrus Design SR20 Pilot’s Operating
Handbook. This document must be carried in the airplane at all times.
Information in this supplement adds to, supersedes, or deletes
information in the basic SR20 Pilot’s Operating Handbook.
• Note •
This POH Supplement Revision dated Revision 02: 07-18-05
supersedes and replaces Revision 01 of this supplement
dated 12-07-04.
Revision 02: 07-18-05
2 of 16 P/N 11934-S27
Section 9 Cirrus Design
Supplements SR20
Section 1 - General
This airplane is equipped with an S-TEC System 55SR Autopilot. The
System 55SR autopilot is a two-axis autopilot system. The system
consists of a flight guidance programmer/computer, altitude
transducer, turn coordinator, and primary flight display (PFD). Mode
selection is made on the programmer/computer panel. A button on
each control yoke handle may be used to disengage the autopilot. The
autopilot makes roll changes through the aileron trim motor and spring
cartridge and makes pitch changes for altitude hold through the
elevator trim motor. The autopilot operates on 28 VDC supplied
through the 5-amp AUTOPILOT circuit breaker on the Essential Bus.
The S-Tec System 55SR Autopilot features:
• Heading Hold and Command.
• NAV/LOC/GPS tracking; HI and LO sensitivity.
• Altitude Hold and Command.
• Vertical Speed Hold and Command.
• GPS Steering (GPSS) for smoother turns onto a course or
during course tracking.
Refer to S-Tec System Fifty-Five SR Autopilot Pilot’s Operating
Handbook (POH), P/N 87127 dated 01 September 2003 or later
revision for full operational procedures and description of implemented
modes.
• Note •
The SR20 implementation of the System 55SR Autopilot does
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西銳20飛機信息手冊CIRRUS DESIGN SR20 AIRPLANE INFORMATION MA(115)