曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

direct the incoming air to the engine and over the engine cylinder
cooling fins where the heat transfer takes place. The heated air exits
the engine compartment through two vents in the aft portion of the
cowling. No movable cowl flaps are used.
March 2010
7-38 Information Manual
Section 7 Cirrus Design
Airplane and Systems Description SR22
Propeller
The airplane is equipped with a constant-speed, aluminum-alloy
propeller with a three-blade (78" diameter) propeller and governor.
The propeller governor automatically adjusts propeller pitch to
regulate propeller and engine RPM. The propeller governor senses
engine speed by means of flyweights and senses throttle setting
through a cable connected to the power (throttle) control lever in the
cockpit. The propeller governor boosts oil pressure in order to regulate
propeller pitch position. Moving the throttle lever forward causes the
governor to meter less high-pressure oil to the propeller hub allowing
centrifugal force acting on the blades to lower the propeller pitch for
higher RPM operation. Reducing the power (throttle) lever position
causes the governor to meter more high-pressure oil to the propeller
hub forcing the blades to a higher pitch, lower RPM, position. During
stabilized flight, the governor automatically adjusts propeller pitch in
order to maintain an RPM setting (throttle position). Any change in
airspeed or load on the propeller results in a change in propeller pitch.
March 2010
Cirrus Design Section 7
SR22 Airplane and Systems Description
Information Manual 7-39
Fuel System
An 92-gallon usable wet-wing fuel storage system provides fuel for
engine operation. The system consists of a 47.25-gallon capacity (46-
gallon usable) vented integral fuel tank and a fuel collector/sump in
each wing, a three position selector valve, an electric fuel pump, and
an engine-driven fuel pump. Fuel is gravity fed from each tank to the
associated collector sumps where the engine-driven fuel pump draws
fuel through a filter and selector valve to pressure feed the engine fuel
injection system. The electric fuel pump is provided for engine priming
and vapor suppression.
Each integral wing fuel tank has a filler cap in the upper surface of
each wing for fuel servicing. Access panels in the lower surface of
each wing allow access to the associated wet compartment (tank) for
inspection and maintenance. Float-type fuel quantity sensors in each
wing tank supply fuel level information to the fuel quantity gages.
Positive pressure in the tank is maintained through a vent line from
each wing tank. Fuel, from each wing tank, gravity feeds through
strainers and a flapper valve to the associated collector tank in each
wing. Each collector tank/sump incorporates a flush mounted fuel
drain and a vent to the associated fuel tank.
The engine-driven fuel pump pulls filtered fuel from the two collector
tanks through a three-position (LEFT-RIGHT-OFF) selector valve. The
selector valve allows tank selection. From the fuel pump, the fuel is
metered to a flow divider, and delivered to the individual cylinders.
Excess fuel is returned to the selected tank.
A dual-reading fuel-quantity gage is located in the center console next
to the fuel selector in plain view of the pilot. Fuel shutoff and tank
selection is positioned nearby for easy access.
Fuel system venting is essential to system operation. Blockage of the
system will result in decreasing fuel flow and eventual engine fuel
starvation and stoppage. Venting is accomplished independently from
each tank by a vent line leading to a NACA-type vent mounted in an
access panel underneath the wing near each wing tip.
The airplane may be serviced to a reduced capacity to permit heavier
cabin loadings. This is accomplished by filling each tank to a tab
visible below the fuel filler, giving a reduced fuel load of 30.0 gallons
usable in each tank (60 gallons total usable in all flight conditions).
Drain valves at the system low points allow draining the system for
maintenance and for examination of fuel in the system for
March 2010
7-40 Information Manual
Section 7 Cirrus Design
Airplane and Systems Description SR22
contamination and grade. The fuel must be sampled prior to each
flight. A sampler cup is provided to drain a small amount of fuel from
the wing tank drains, the collector tank drains, and the gascolator
drain. If takeoff weight limitations for the next flight permit, the fuel
tanks should be filled after each flight to prevent condensation.
Fuel Selector Valve
A fuel selector valve, located at the rear of the center console,
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西銳20飛機信息手冊 SR22 AIRPLANE INFORMATION MANUAL 2979(64)