Horizontal-Stabilizer Rib Station
 Figure 002
 1EFF :  ALL  1  06-31-55 Page 3 
1  1  Feb 01/98
 1  1
 1CES  1

 WINGS - DESCRIPTION AND OPERATION
_________________________________
 1. General
_______
 A. Wing Rib Stations R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 (Ref. Fig. 001)
 **ON A/C 301-399,

 (Ref. Fig. 001A)
 **ON A/C ALL

 All stations are parallel to the aircraft X axis. All measurements are:
 -at 90 degrees to RIB 1
 -measured between RIB 1 and the intersection of each rib datum with the front spar datum.
 1EFF : ALL 1 06-31-57Page 1 1 1 Aug 01/05 1 1 1CES 1

 Wing Rib Stations
 Figure 001

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 06-31-57Page 2 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

R  Wing Rib Stations 
R  Figure 001A
 1EFF :  301-399,  1  06-31-57 Page 3 
1  1  May 01/04
 1  1
 1CES  1

 ACCESS - DESCRIPTION AND OPERATION
__________________________________
 1. General
_______
 The components below have an identification of access panels or doors:

 -access doors for maintenance,
 -service doors,
 -fillets,
 -fairings,
 -
removable access panels of the radio rack,

 -
removable floor panels,

 -
removable cargo compartment panels,

 -
removable ceiling panels.

 NOTE : This list does not include the electrical panels. Their
____
 identification since they are covered by a specific rule.

 A. Identification Method
 The identification includes:

 (1)
 Three figures which identify the zone of the door.

 (2)
 A suffix of two letters:

 -
The first or identification letter identifies the door in a logical sequence, ie. from the inside to the outside, or from forward to aft. The first identification letter is an 'A' for each zone.

 -
The second or location letter, gives the location of the door on the aircraft if necessary. T = Top (Upper Surface) B = Bottom (Lower Surface) L = Left R = Right Z = Internal F = Floor panel W = Sidewall panel C = Ceiling panel

 When all the letters of the alphabet are used, panels are identified as follows:
 -the letter A is the identification letter
 -letters U, D, P, S, G, X, Y are the location letters: U = Top (Upper Surface) D = Bottom (Lower Surface) P = Left S = Right G = Floor panel X = Sidewall panel Y = Ceiling panel
 1EFF : ALL 1 06-40-00Page 1 1 1 Feb 01/98 1 1 1CES 1 NOTE : The letters I and O are not used.

____
 Examples for the identification of an access door:

 -121 AL is the first panel in zone 121 on Left side (forward fuselage)
 -191 AT is the first panel in zone 191 at Top (belly fairing)
 B. General Rules
 (1)
 The cabin passenger/crew doors, cargo compartment and main landing gear doors are only identified by the zone number, since each of these doors is a zone in itself.

 (2)
 The letters I and O are not used.

 (3)
 Pressure relief doors or air vents have no identification numbers.

 (4)
 Doors along the aircraft centerline have the left side zone number.

 (5)
 The vertical stabilizer and rudder doors are numbered from the bottom to the upper part.

 (6)
 Identical doors on either side of the aircraft have the same
 identification letter even if the zone numbers are different.

 (7)
 When a door is on a larger door it is identified with two letters after the identification of the large door.

 (8)
 When a door is in more than one zone, use the smallest zone number.

 (9)
 A door on a zone boundary is numbered according to the zone in which it is removed.

 NOTE : The various access doors are in the subject of the related ATA
____
 reference.

 1EFF : ALL 1 06-40-00Page 2 1 1 Feb 01/98 1 1 1CES 1

 DOORS - DESCRIPTION AND OPERATION
_________________________________
R  **ON A/C 001-049, 051-099, 101-149, 201-299,
 1. General_______ This topic identifies the access panels installed on the doors.
 A. Passenger/Crew Doors
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 尺寸和區域(9)