(e)  
Repeat steps (c) and (d) for T27A bearing switch positions of 90.-TO and 270.-TO with corresponding course counter setting on AP/FD MSP. Check that HSI test displays are the same as in step (c) and (d) and that RMI VOR bearing displays follow signal generator bearing switch settings.

 (f)  
Check that AP/FD MSP course counters are set to 270.

 (g)  
Position T27A bearing switch to 270.-FROM. Check that HSI NAV flag is out of view, course deviation bar is centered and to/from indicator points to tail of course arrow.

 (h)  
Depress T27A TONE switch and check for 1020 Hz tone thru an interphone station with VOR/ILS monitoring.

 (i)  
Release T27A POWER switch.

 (3)  ILS Test
 (a)  
Tune VOR/ILS navigation systems to ILS test frequencies. Check that ADI and HSI glide slope flag and pointers appear, that HSI to/from indicator goes out-of-view, and that RMI VOR bearing pointers stow at 3 o'clock.

 (b)  
Position T28A Localizer Test Set and T29A Glide Slope Test Set course switches to ON COURSE and extend T28A and T29A antennas.

 (c)  
Hold both T28A and T29A POWER switches in ON position using switch gang bar. Check that ADI and HSI GS flags and HSI striped NAV flag go out of view and that HSI course deviation bar and ADI and HSI glide slope pointers are centered.

 (d)  
Position T28A course switch to LEFT and T29A course switch to UP. On ADI and HSI, check that glide slope pointers drive up to second dot and that course deviation bar drives to outer left dot.

 EFFECTIVITY

 
 ALL  04 Page 516  Apr 25/8934-31-00
 (e)  
Position T28A course switch to RIGHT and T29A course switch to DOWN. On ADI and HSI, check that glide slope pointers drive down to second dot and that course deviation bar drives to outer right dot.

 (f)  
Position T28A and T29A course switches to ON COURSE. On ADI and HSI, check that course deviation bar and glide slope pointers center.

 (g)  
Position T28A and T29A delete switches to 90 cycle DELETE. On ADI and HSI, check that course deviation bar drives out past outer left dot, that glide slope pointers drive to full scale up, and that GS and NAV flags appear.

 (h)  
Position T28A and T29A delete switches to 150 cycle DELETE. On ADI and HSI, check that course deviation bar drives out past outer right dot, that glide slope pointers drive to full scale down, and that GS and NAV flags appear.

 (i)  
Release T28A and T29A delete switches. On ADI and HSI, check that GS and NAV flags disappear and that glide slope pointers and course deviation bars return to center.

 (j)  
Release T28A and T29A POWER switches. On ADI and HSI, check that GS and NAV flags appear.

 (k)  
Turn off equipment and remove electrical power if no longer required.

 EFFECTIVITY

 
 ALL  02 Page 517  Aug 25/8834-31-00
 XA 7. __________________
VOR Automatic Test (on LH airplanes only) XA A. VOR-automatic test XA (1) Very phase-modulation portion of the VOR test signal and verify XA data in the following table. Watch for periodic RMI error. XA ~êêê XA  Variable Phase Signal  RMI Narrow  TO-FROM  Dev Needle  XA  (Degrees)  Needles (| 3.)    XA è”””. XA  0  0  TO  Centered  XA  45  45  TO  Full Right  XA  90  90  *[1]  Full Right  XA      XA  135  135  FROM  Full Right  XA  180  180  FROM  Centered  XA  225  225  FROM  Full Left  XA      XA  270  270  *[1]  Full Left  XA  315  315  TO  Full Left  XA  0  0  TO  Centered  XA ééé
 *[1] To-from swing shall occur between 88 and 92 degrees and between 268 and 272 degrees. XA 8. _________
ILS Tests (on LH airplanes only) XA A. Localizer Test XA (1) Set AP/FD mode selector to LAND, apply 109.10 MHz on course XA localizer signal. Tune frequency on captain's VHF NAV control panel XA to localizer signal and verify that captain's HSI deviation needle XA and ADI deviation pointer are centered. XA (2) Switch on FD. XA (3) Vary signal generator modulation controls to produce a localizer XA deviation test signal which causes a 2-dot fly-right indication on XA captain's HSI. Observe that localizer flag is out of view. XA (4) Slowly decrease test signal modulation to center deviation needle XA on HSI while observing ADI. Note that ADI localizer indication XA comes into view at approximately 1/2-dot deviation on the HSI. XA (5) Verify that LOC and runway flags are out of view. XA (6) Re-center deviation needle. XA (7) Again vary the signal modulation to produce a 2-dot fly-right XA indication on the HSI.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747飛機維護手冊AMM CHAPTER 34 - NAVIGATION 第34章導航2(34)