LPTACC Valve
Figure 401/TASK 75-22-10-991-300- 22 (SHEET 2)
F EEFF : ALL 『E 75-22-10 Page 405
E E Feb 01/98
E E
ECES E
Exploded View of LPTACC Valve Installation
Figure 402/TASK 75-22-10-991-301- 12 (SHEET 1)
F EEFF : ALL 『E 75-22-10 Page 406
E E Feb 01/98
E E
ECES E
Exploded View of LPTACC Valve Installation
Figure 402/TASK 75-22-10-991-301- 22 (SHEET 2)
F EEFF : ALL 『E 75-22-10 Page 407
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E E E NOTE : The inboard bracket (130), which is core engine bracket, is
____
not removed.
(9) Disassemble the LPTACC valve (90), the bracket (150) and the airscoop
(100) to move these 3 items apart:
(a) Put the assembly on a workbench.
(b) Remove the 6 bolts (70) which attach:
- The large, vertical leg of item (150) to the item (100) with the circular flange of item (90) in between. Thus, remove 2 bolts (70).
- The circular flange of item (90) directly to the item (100). Thus, remove the last 4 bolts (70).
(c) Remove the 2 bolts (160) which attach the small, horizontal leg of item (150) directly to the body of valve (90).
(10) Put blanking plugs on the disconnected line ends.
(11) Put blanking caps and/or protective covers on all the disconnected air and fuel orifices of items (90), (50), (100), (80) and (20).
F 『 EEFF : ALL E Page 40875-22-10
E E Aug 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 75-22-10-400-002
Installation of the Low Pressure Turbine Active Clearance Control (LPTACC) Valve
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 1 m (3 ft. 3 in.)
No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2101 USA MIL-T-5544
graphite grease (Ref. 70-30-00)
Material No. CP2442 *
engine oil (Ref. 70-30-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
40 gasket 75-22-10 01B-030
40 gasket 75-22-10 01B-030A R 40 gasket 75-22-10 01B-030B R 40 gasket 75-22-10 01B-030C
F 『 EEFF : ALL E Page 40975-22-10
E E Aug 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
R from the External Power 71-00-00-710-006 Minimum Idle Check 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-36-00-010-040 Opening of the Thrust Reverser Doors
78-36-00-410-040 Closing of the Thrust Reverser Doors
75-22-10-991-300 Fig. 401
75-22-10-991-301 Fig. 402
3. Job Set-up
__________
Subtask 75-22-10-860-051
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2). 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM AIR 空氣(17)
