- replace the RECEIVER-ILS, 1 (2RT1) (Ref. AMM TASK 34-36-31-000-001) and (Ref. AMM TASK 34-36-31-400-001).
(2) If the fault continues:
- remove the ILS receiver 1
- remove the DMC 1
- do a check and repair the wiring of the ILS 1 INPUT signal from ILS receiver 1 (2RT1) pins AB/11B, 11C to DMC 1 (1WT1) pins AA/6A, 6B (Ref. ASM 34-36/01)
- install the ILS receiver 1
- install the DMC 1.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-004, 051-060, ∞∞31-63-00∞∞∞∞∞∞∞∞∞∞Page B295
Aug 01/05 CES
B. Do the test given in Para. 3.
Loss of the ILS 2 Test Display
1. Possible Causes
_______________
- DMC-2 (1WT2)
- RECEIVER-ILS, 2 (2RT2)
- wiring of the ILS 2 INPUT signal
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
AMM 34-36-00-740-002 BITE Test of the ILS
AMM 34-36-31-000-001 Removal of the ILS Receiver (2RT1,2RT2)
AMM 34-36-31-400-001 Installation of the ILS Receiver (2RT1,2RT2)
ASM 34-36/01
3. Fault Confirmation
__________________
A. Test Do the BITE test of the ILS (system 2) (Ref. AMM TASK 34-36-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message DMC2(1WT2)/ILS2(2RT2):
- replace the DMC-2 (1WT2) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- replace the RECEIVER-ILS, 2 (2RT2) (Ref. AMM TASK 34-36-31-000-001) and (Ref. AMM TASK 34-36-31-400-001).
(2) If the fault continues:
- remove the ILS receiver 2
- remove the DMC 2
- do a check and repair the wiring of the ILS 2 INPUT signal from ILS receiver 2 (2RT2) pins AB/11B, 11C to DMC 2 (1WT2) pins AA/6J, 6K (Ref. ASM 34-36/01)
- install the ILS receiver 2
- install the DMC 2.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-004, 051-060, ∞∞31-63-00∞∞∞∞∞∞∞∞∞∞Page B297
Aug 01/05 CES TASK 31-63-00-810-969
No EFIS Data with EIS DMC Selector Switch at CAPT/3 and/or F/O/3
1. Possible Causes
_______________
- SEL SW EIS DMC (18WT)
- wiring of the EIS DMC Selector Switch (18WT)
- wiring from the DMC3 (1WT3) pin AC/7 to the ground terminal
- RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT)
- C/B-EIS/DMC3/STBY/SPLY (14WT1)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
ASM 31-61/02
ASM 31-68/02
3. Fault Confirmation
__________________
A. Not applicable, the fault is evident.
4. Fault Isolation
_______________
A. If there is no EFIS Display with EIS DMC Selector Switch (18WT) at CAPT/3:
- remove the DMC3 (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
- do a check for a ground signal at pin AB/4C of DMC3.
(1) If there is no ground signal:
- replace the SEL SW EIS DMC (18WT).
(a) If there is no ground signal:
- do a check and repair the wiring of the EIS DMC Selector Switch (18WT): pin 2 to the DMC3 pin AB/4C (Ref. ASM 31-68/02).
(2) If there is a ground signal:
- refer to the trouble shooting procedure related to the DMC3 maintenance message.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : ALL ∞∞31-63-00∞∞∞∞∞∞∞∞∞∞Page B298
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統(tǒng) 2(108)
