(2)
The airplane should not be in or near a large metallic structure, such as a hanger or tower, which may attenuate RF energy. Airplane structure, such as landing gears, may block the VHF antenna when the airplane is in certain positions with respect to ground station antennas.
WARNING: DO NOT KEY THE VHF TRANSMITTERS WHEN THE AIRPLANE IS BEING FUELED.
B. Prepare to Test
(1)
Provide ground power to the airplane and energize busses on load control centers P6 and P18.
(2)
Ensure the radio bus master switches are closed.
(3)
Ensure all VHF circuit breakers and interphone circuit breakers are closed.
(4)
Allow 5 minutes for system warmup.
(5)
Check flight interphone system and ensure audio selector panels are operable (Ref 23-52-0).
C. Test VHF Communication System
(1)
At captain's station, select VHF-1 with mike selector switch. Corresponding indicator light on audio selector panel shall come on.
(2)
At first officer's station, select VHF-2 with mike selector switch. Corresponding indicator light on audio selector panel shall come on.
(3)
Tune each VHF system to an unused frequency and operate the COMM TEST button on the VHF control panel. The receiver shall operate at maximum sensitivity as verified by an increase in background noise.
(4)
Position the VHF control panels transfer switches to the left and tune each VHF system to an active frequency with the left set of controls and that the other frequency indicator window is flagged. Listen to communications traffic and compare receiver sensitivity. They should be approximately equal. All but the weakest signals should open squelch.
(5)
Rotate VHF system volume control on audio selector panel and confirm control works smoothly through entire range.
(6)
Tune each system to several different channels and ensure operation is good by channeling from both above and below the selected frequency. Compare reception between receivers; reception should be approximately equal.
(7)
Position the transfer switch on each VHF control panel to the right and repeat steps C.(4) thru C.(6). Results shall be similar.
(8)
Tune VHF-1 system to an authorized test frequency. Key the system and establish communication. Check TRANSMIT MONITOR light on front panel of transceiver comes on when transmitting and that the light flickers when modulating. Transmission and reception should be loud and clear. Sidetone should be clearly audible when transmitting.
CAUTION: DO NOT KEY THE VHF TRANSMITTERS WHEN AIRPLANE IS BEING FUELED. AVOID KEYING THE TRANSMITTER IF RECEPTION IS NOT SATISFACTORY. (LACK OF CLEAR RECEPTION MAY BE AN INDICATION OF AN OPEN TRANSMISSION LINE.)
(9)
Repeat step C.(8) for VHF-2 system.
(10)
Repeat steps C.(l) thru C.(8) for any combination of VHF system and audio selector panel, where a test is needed. Reception and transmitter sidetone shall be loud and clear.
NOTE: Push up VHF toggle switches if only monitoring is to be done. The mike selector switch connects both receiving and microphone circuits to the systems.
5C8
Jun 20/85 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 23-21-01 Page 501
519
23-21-01 Page 502 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Nov 15/77
D. Test VHF Transceiver
(1)
Connect headset and microphone to VHF transceiver on electronic equipment rack E2.
(2)
Press SQUELCH DISABLE button on transceiver. Listen for receiver noise.
(3)
Release button and check that noise cuts off.
(4)
Press microphone PTT button. Check that TRANSMIT MONITOR light comes on.
(5)
Talk into mike and listen for sidetone in headset. Check that TRANSMIT MONITOR light varies in intensity with modulation. Release PTT button.
(6)
Secure VHF systems.
(7)
Determine whether there is any further need for electrical power on the airplane; if not, remove external power.
504
Feb 15/81 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 23-21-01 Page 503
VHF ANTENNA - REMOVAL/INSTALLATION
1. Equipment and Materials
A. Cleaning solvent (Ref 20-30-31, Cleaners and Polishes)
B. Gauze
C. Aerodynamic smoother (Ref 20-30-11, Sealants and Sealing Material)
2. Remove VHF Antenna (Fig. 401)
A. Remove aerodynamic smoother around the antenna base.
B. Remove 10 mounting screws from antenna base.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機(jī)維護(hù)手冊 通訊 COMMUNICATIONS(20)
