曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

3  QUADRANT  ID  0.3120  0.3130  0.3136  0.0030  X 
BOLT  OD  0.3110  0.3120  0.3106  X 
4  BUSHING  ID  0.5000  0.5015  0.5055  0.0060  X 
BUSHING  OD  0.4985  0.4995  0.4940  X 
5  BUSHING  ID  0.3750  0.3760  0.3760  0.0029 
BOLT  OD  0.3735  0.3745  0.3731 
6  BEARING  ID  0.3745  0.3750  0.3750  0.0019 *[1]  X 
BOLT  OD  0.3735  0.3745  0.3731  X 
7  BUSHING  ID  0.3750  0.3765  0.3805  0.0060  X 
BOLT  OD  0.3735  0.3745  0.3690  X 
8  BUSHING  ID  0.3125  0.3140  0.3180  0.0060  X 
BOLT  OD  0.3110  0.3120  0.3065  X 

*[1] REPLACE BEARING WHEN RADIAL PLAY EXCEEDS 0.0020 INCH.
*[2] REPLACE AILERON CONTROL ROD WHEN BEARING RADIAL PLAY EXCEEDS 0.0020 INCH.

Aileron Wing Quadrant Wear Limits  500 
27-11-111  Figure 601 (Sheet 2)  Aug 15/73 
Page 602 
B
O
E
I
NG
P
R
OP
R
I
E
T
A
R
Y
 - Copyri
ght
 . - Unpubl
i
s
hed
W
o
r
k
 -
S
ee
t
i
t
l
e page f
o
r de
t
a
i
l
s
.
 

AILERON TRIM CONTROL UNIT - REMOVAL/INSTALLATION
1.  Equipment and Materials
A.  Tensiometer, 0- to 100-pound capacity
B.  Rigging Pins Kit - F70207-3, -52, -61, or -84:
REF NO.  70207-( )  DIAMETER (INCHES)  LENGTH (INCHES)  FUNCTION 
A/S-13  -8  0.309 - 0.311  3.7 + 0.25  Aileron Trim Gearbox 

2.  Remove Aileron Trim Control Unit
A.  Place aileron trim control knob indicator in zero trim position (Fig. 401).
B.  Insert rigging pin A/S-13 in aileron trim gearbox.
C.  Remove access panel from right side of control stand.
D.  Disconnect electrical wires from base of aileron trim wheel.
E.  Disconnect cables ATA and ATB at turnbuckles.
F.  Use phenolic faced clamps and secure aileron trim cables ATA and ATB aft of turnbuckles.
G.  Tag disconnected cables to facilitate reassembly.
H.  Remove aileron trim knob as follows:
(1)  
Remove three mounting screws.

(2)  
Remove assembly of aileron trim knob and adapter plate from spline on aft bearing housing.

(3)  
If relamping or replacement of aileron trim knob is required, remove screws and washers retaining adapter plate to aileron trim knob.

I.  Remove four screws retaining aft bearing housing to control stand structure.
J.  Remove nuts, washers, and screws retaining forward bearing support to structure.
K.  Remove trim control unit from control stand.
506 
Feb 20/88  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  27-11-121 Page 401 

G05698 G05713 G05724
Aileron Trim Control Unit Installation  500 
27-11-121 Page 402  Figure 401 (Sheet 1) BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  May 15/68 

500  Aileron Trim Control Unit Installation 
May 15/68  Figure 401 (Sheet 2) BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  27-11-121 Page 403 

Aileron Trim Control Unit Installation  506 
27-11-121 Page 404  Figure 401 (Sheet 3) BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  May 15/69 

L.  Disassemble aileron trim control unit as follows;
(1)  
Remove nut and washer to separate aft bearing housing from shaft.

(2)  
Remove screws and washers to separate retainer plate from aft bearing housing.

(3)  
Remove retainer ring and separate stop assembly from shaft.

(4)  
Remove nut, washer, and screw securing cable drum to shaft and remove sleeve.

(5)  
Separate forward bearing support from shaft, and remove cable drum.

(6)  
Remove cables ATA and ATB from cable drum.

3.  Install Aileron Trim Control Unit
A.  If used bolts, bushings, bearings or other components with wear limits are being installed, check for allowable wear (Ref 27-11-121, Inspection/Check).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(92)