30-34-00
 ALL  ú ú 01 Page 504 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 CAUTION: DO NOT OPERATE THE PROBE HEATERS FOR MORE THAN 30 SECONDS.
_______ STOP FOR 5 MINUTES AFTER YOU OPERATE THE PROBE HEATER. YOU WILL DAMAGE THE PROBE IF YOU OPERATE THE PROBE HEATER FOR TOO LONG.
 (a)  
Open 7F23, LANDING GEAR DSP & CONT ALTN circuit breaker on the P7, Overhead Circuit Breaker Panel.

 WARNING:_______DO NOT TOUCH THE PROBE. THE PROBE HEATER CAN BURN YOU.

 (b)  
Hold your hand near the probe and make sure that the probe temperature increases.

 (c)  
Close 7F23, LANDING GEAR DSP & CONT ALTN circuit breaker on the P7, Overhead Circuit Breaker Panel.

 (d)  
Make sure that the probe temperature does not continue to increase.

 S 715-022
 (5) Do a check of the probe heater operation in the engine-on mode:
 (a)  
Open 6H23, PROBE HEAT ENG 3 circuit breaker on the P6, Main Power Distribution Panel.

 (b)  
Set the S2 switch on the engine 3 N2 speed card YMLA005 (in the forward electrical systems card file M7603) to TEST.

 (c)  
Close 6H23, PROBE HEAT ENG 3 circuit breaker on the P6, Main Power Distribution Panel.

 (d)  
Make sure that the probe temperature increases.

 (e)  
Open 6H23, PROBE HEAT ENG 3 circuit breaker on the P6, Main Power Distribution Panel.

 (f)  
Set the S2 switch on the YMLA005 card to NORMAL.

 H. Engine 4, PT2/TT2 Probe Heat Test
 S 865-023
 (1)  
Close 6H25, PROBE HEAT ENG 4 circuit breaker on the P6, Main Power Distribution Panel.

 S 865-024

 (2)  
Make sure that these circuit breakers on the P6, Main Power
 Distribution Panel are open:

 (a)  
6H19, PROBE HEAT ENG 1

 (b)  
6H21, PROBE HEAT ENG 2

 (c)  
6H23, PROBE HEAT ENG 3

 (3)  
Get access to the engine 4, PT2/TT2 probe.

 S 015-026
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 30-34-00
 ALL  ú ú 01 Page 505 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 715-027
 (4)  Do a check of the probe heater operation in the air mode:
 CAUTION: DO NOT OPERATE THE PROBE HEATERS FOR MORE THAN 30 SECONDS.
_______ STOP FOR 5 MINUTES AFTER YOU OPERATE THE PROBE HEATER. YOU WILL DAMAGE THE PROBE IF YOU OPERATE THE PROBE HEATER FOR TOO LONG.
 (a)  
Open 7H8, GND SAFETY RELAY circuit breaker on the P7, Overhead Circuit Breaker Panel.

 WARNING:_______DO NOT TOUCH THE PROBE. THE PROBE HEATER CAN BURN YOU.

 (b)  
Hold your hand near the probe and make sure that the probe temperature increases.

 (c)  
Close 7H8, GND SAFETY RELAY circuit breaker on the P7, Overhead Circuit Breaker Panel.

 (d)  
Make sure that the probe temperature does not continue to increase.

 S 715-028
 (5) Do a check of the probe heater operation in the engine-on mode:
 (a)  
Open 6H25, PROBE HEAT ENG 4 circuit breaker on the P6, Main Power Distribution Panel.

 (b)  
Set the S2 switch on the engine 4 N2 speed card YMLA007 (in the forward electrical systems card file M7603) to TEST.

 (c)  
Close 6H25, PROBE HEAT ENG 4 circuit breaker on the P6, Main Power Distribution Panel.

 (d)  
Make sure that the probe temperature increases.

 (e)  
Open 6H25, PROBE HEAT ENG 4 circuit breaker on the P6, Main Power Distribution Panel.

 (f)  
Set the S2 switch on the YMLA007 card to NORMAL.

 I. Put the Airplane to Its Initial Condition
 S 445-032
 (1)  
Do this task: "Put Safety-Sensitive Systems Back to the Condition before Air Mode Simulation" (AMM 32-09-02/201).

 S 865-029

 (2)  
Close these circuit breakers on the P6, Main Power Distribution Panel:

 (a)  6H19, PROBE HEAT ENG 1
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 防冰和排雨 ICE AND RAIN PROTECTION(43)