曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Data System (AIDS) via either MCDU, the user has to
press the AIDS line select key from the MCDU MENU page.
The AIDS MCDU menu page is then displayed.
Some of the AIDS functions may be controlled from this
menu.
The DMU only communicates with one MCDU at a time.
The AIDS selection from a second MCDU generates, on
this MCDU, the message "AIDS (TIMEOUT)".
TMUAI2D03-T01 LEVEL 1
EFFECTIVITY 31-36-00 Page 2
Jul 31/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 31 INDICATING/RECORDING SYSTEMS
UF94200
EFFECTIVITY Page 426
ALL
AIDS: AIDS MCDU MENU PRESENTATION - GAINING ACCESS
TMUAI2D03-P01 LEVEL 1
EFFECTIVITY 31-36-00 Page 3
Jul 31/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 31 INDICATING/RECORDING SYSTEMS
UF94200
EFFECTIVITY Page 427
ALL
AIDS: AIDS MCDU MENU PRESENTATION
OPTIONAL ITEMS
PCMCIA
Only displayed if the DMU is equipped with a Personal
Computer Memory Card International Association
(PCMCIA) interface.
This is to access the PCMCIA disk management and
display functions.
The status of the PCMCIA disk, used as a Digital AIDS
Recorder (DAR), is also displayed. E.g. RUN.
MICRO 3
Only displayed if the DMU is equipped with a third
microprocessor board for expanded customer
programmable functions.
This is to access additional menus.
DAR START/STOP CONTROLS
Only displayed if either a DAR is installed or the DMU
is equipped with a PCMCIA interface.
The last line provides manual start and stop of the
DAR, if the DAR has not been already started
automatically.
The DAR status indication is displayed on the left
(RUNNING, STOPPED, FAILED).
PARAMETER CALL-UP
The parameter call-up functions enable real time
parameter read out.
Reading parameters in real time may be helpful in
advanced trouble shooting.
Parameters acquired by the DMU can be displayed:
- either in raw values if they are called by
their ARINC 429 characteristics (PARAMETER
LABEL CALL-UP function),
- or in engineering values if they are called by
their alphanumeric code (PARAMETER ALPHA
CALL-UP function).
If programmed with the Ground Support Equipment (GSE),
predefined lists of parameters (provided with an alpha
call-up) can also be displayed.
LOAD STATUS
This is to access the loading status of the AIDS
software and database.
E.g. TRANSFER IN PROGRESS.
TMUAI2D03-T02 LEVEL 1
EFFECTIVITY 31-36-00 Page 4
Jul 31/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 31 INDICATING/RECORDING SYSTEMS
UF94200
EFFECTIVITY Page 428
ALL
AIDS: AIDS MCDU MENU PRESENTATION
TMUAI2D03-P02 LEVEL 1
EFFECTIVITY 31-36-00 Page 5
Jul 31/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 31 INDICATING/RECORDING SYSTEMS
UF94200
EFFECTIVITY Page 429
ALL
AIDS: AIDS MCDU MENU PRESENTATION
PROGRAMMING
This is to access the AIDS hardware and software
identification as well as the programming menus.
The programming is performed at the engineering level,
partially on the MCDU, mostly on the GSE.
A password, defined with the GSE, is necessary to
program the system with the MCDU.
The few programmable features with the MCDU are:
- inhibition, until the next DMU power off, of
the report printing and/or linking to the Air
Traffic Service Unit (ATSU),
- change of the report limits and counters,
- initialization and visualization of the
engine/APU hours and cycles.
SAR/DAR
This is to access the summary and history of the Smart
AIDS Recorder (SAR) stored data sets.
It is also possible to start and stop the SAR recording
manually and to display Digital AIDS Recorder (DAR)
data, if a DAR is installed.
LIST OF PREVIOUS REPORTS
This is to display the list of the last twenty stored
reports.
The reports are listed with their number, their trigger
code and the date, time and flight leg of their
generation.
STORED REPORTS
This is to display the list of all stored reports per
type of report.
The reports are listed with their trigger code and the
date, time and flight leg of their generation.
It is then possible to print and/or send each report
independently.
REPORTS MANUAL REQUEST
This is to individually generate any standard or user
programmed report via a manual request on the MCDU.
The report can then be printed, sent via ATSU or simply
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：ATA 31 INDICATING AND RECORDING SYSTEM(56)