曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

finger lift lever for thrust reverser operation, Takeoff/
Go Around (TOGA) switches, autothrottle
engage and disengage switches, quick disconnect and engine run switches.
Pressing the TOGA switches will change the pitch and roll on the command bars on the PFD. For
more information, see Chapter 4, AFCS.
The autothrottle is engaged by pressing the left and/or right engage/disengage switch(es). It is
disengaged by a second press of either engage/disengage switch or by pressing either autothrottle
quick disconnect button or by moving the thrust lever manually.
Selecting the ENGINE RUN switches to ON activates fuel pumps, opens the HPSOV in the fuel
management unit and initiates the start sequence. Selecting the ENGINE RUN switches to OFF
deactivates
fuel pumps, closes the HPSOV and shuts down the engine.
GF1810_042
TAKEOFF/
GO AROUND
(TO/GA) SWITCH
AUTOTHROTTLE
QUICK DISCONNECT
ENGINE RUN
SWITCHES
REVERSE THRUST
LEVER
REVERSE THRUST
LEVER
AUTOTHROTTLE
QUICK DISCONNECT
TOGA SWITCH
AUTOTHROTTLE
SWITCH
IDLE
Idle Forward Thrust
MAX THRUST
Maximum Forward Thrust
REV
Idle Reverse Thrust
MAX REV
Maximum Reverse Thrust
ENGAGE/DISENGAGE
IDLE
REV
MAX REV
MAX
THRUST
ENGINE
L RUN R
OFF OFF
POWER PLANT
REV 41, Jul 08, 2004 Flight Crew Operating Manual
CSP 700−6
Volume 2
18−10−29
AUTOTHROTTLE SYSTEM
The dual Autothrottle (A/T) system provides, full flight regime, thrust management via automatic
positioning of the thrust levers. The A/T system modulates thrust, through dual throttle servo controls,
to provide thrust control and speed control. The A/T system can only be used when in EPR control
mode.
The PFD displays A/T engage status, operating mode and faults. All A/T faults are annunciated on
EICAS.
The dual Electronic Thrust Trim System (ETTS) provides limited authority thrust trimming, over the
full flight regime, via electronic trim commands to the FADEC.
The ETTS provides EPR trim, N1 synchronization, N2 synchronization, engage status as well as fault
annunciation on EICAS.
GF1810_043
The A/T − ETTS system contains the following :
· AT/ETTS software which coresides
and coexecutes
with the FMS software, on the processor
of the FMS card, in Integrated Avionics Computers’ (IACs) #1 and #2.
· Interface with the Throttle Quadrant Assembly (TQA).
· Interface with both FADECs (output via Fault Warning Computers (FWC), input via Data
Acquisition Units’ (DAUs) #1 and #2 for the left and DAUs #3 and #4 for the right engine).
· Two servos located in the TQA.
· Two engage/disengage switches and two quick disconnect switches, located on the thrust
levers.
· An A/T source selection on the MFD menu.
· An EPR rating and a EPR CMD/N1/N2 SYNC selection on the FMS menu.
POWER PLANT
Flight Crew Operating Manual REV 41, Jul 08, 2004
CSP 700−6
Volume 2
18−10−30
AUTOTHROTTLE SYSTEM (CONT'D)
Autothrottle Data Sources
The A/T system is compatible with the active pitch mode, as determined by the AFCS or FMS.
Thrust control is maintained when speed is controlled via pitch control.
The A/T uses sensor data from the coupled PFD, to ensure consistent and compatible operation
with the AFCS. Data received from the AFCS and FMS is selected from the active AFCS and FMS
to ensure A/T control is compatible with the pitch control.
The A/T selects the ADC displayed on the coupled PFD as the ADC source during nondual
coupled Autopilot/Flight Director (AP/FD) operation. During dual coupled AP/FD operation, the A/T
selects the ADC displayed on each PFD and averages the data.
The A/T selects the IRS displayed on the coupled PFD as IRS source during nondual
coupled
AP/FD operation. During dual coupled AP/FD operation, the A/T selects the IRS displayed on each
PFD and averages the data.
The A/T selects the coupled side PFD during single coupled AP/FD operation. During dual coupled
AP/FD operation the A/T continues to use the PFD it was using prior to coupled operation.
The A/T selects and uses status information and data from the active AFCS and the active FMS.
The A/T identifies the active DAU channel via data received from the Fault Warning Computer
(FWC).
The A/T indicates the DAU selected source for the FADEC data and uses status information and
data from the FWC. The FWC monitors the channel in control status, to assess FADEC integrity.
The A/T identifies the active radio altimeter via selection data received from the FWC. The radio
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：龐巴迪挑戰者手冊7(141)