曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

X,p = xac -  Cf
(1,43)
     Thus, the location of the aerodynamic center relative to the center of pressure
depends on the sign of Cmo. For positively cambered'aufoils, Cmo <0 SO that
the center of pressure is aft of the~erodynamic center as shown in Fig. 1.21b.
However, as the angle of attack increases (O s Cl s Cl.max), the center of pressure
moves towards the aerodynanuc center as shown in Fig. 1.22.
1.5.3  Stallof Wing Sections
        Atlow angles of attack, the flow separation occurs at or close to the trailing edge.
As the angle of attackincreases, the separation point gradually moves towards the
leading edge.ln this process, the lift coefficient continues to increase and, at some
point, attains a maximum value. Beyond this value of angle of attack, the lift
coefficient drops, and the airfoilis said to have stalled. This type of stall generally
occurs on thick airfoils and is characterized by a gradualloss of lift beyond the
stall as shown by the curve a in Fig.  1.23.
     For thin airfoils that have sharply curved leading edges, a slightly different type
of stall occurs. From the leading edge and up to the minimum pressure point, a
large favorable pressure gradient exists that tends to promote the existence of a
laminar boundary layer. Beyond the minimum pressure point, an adverse pressure
gradient exists towards the trailing edge. Because of the sharp curvature of the
leading edge of a thin airfoil, the adverse pressure gradientis sufficiently strong to
 cause flow separation. K the Reynolds number is low, this type of flow separation
is of a permanent nature (no subsequent reattachment) and, as a result, the airfoil
stalls. Because the flow separation occurs close to the leading edge, this type of
 stallis usually abrupt and is marked by a sudden loss oflift beyond the maximum
 lift as shown by curve b in Fig. 1.23.
REVIEW OF BASIC AERODYNAMIC PRfNCIPLES                 23
Fig. 1.23    Schematic illustration of stall of airfoil sechons.

;r~
~

~
:~
.:(!
..."...
r#
Fu
l.:t
    :: ::
v
.}7\
:4t
:c::.
f.V
:#
y.
:ta
'ty
=
a
 x!
1;,4
'i/,
:.i;,
h
v,
~
:s
d,
   . dj
24               PERFORMANCE, STABILITY, DYNAMICS, AND CONTROL
a) Plain flap
b) Split flap
c) Fowler flap
d) Slotted flap
e) Kruger nap
f) Leading-edge flap
g) Blown flap
h) Jet flap
Fig.1.24    Schematic diagram of typical flap configurations.
    F/aps.   Flaps are mechanical devices deflected either from the trailing edge
(or close to the trailing edge) or the leading edge. Several different designs of the
fiaps have come into existence, and some of the commonly used configurations
are shown in Fig. 1.24. Flap configurations depicted in Figs. 1.24a-1.24g are
mechanical flaps, and that shown in Fig.  1.24h is the so-called jet flap.
      A deflection of a hinged mechanical fiap basically alters the effective camber of
 the airfoil section, hence its lift-curve slope. The defiection of the flap increases the
value of Cimax without essentially altering the stall angle. Therefore, at the stall,
an airfoil with a deflected fiap will have an incrementallift coefficient ACinax as
shown in Fig. 1.25. The plain fiap, split flap, Kruger fiap, and leading-edge flaps
 belong to this category of plain mechanical flaps.
   In addition to changing the camber, the slotted flap and the Fowler-flap also
act as boundary-layer control devices. A schematic diagram of the operation of a
trailing-edge slotted fiap is shown in Fig. 1.26. High-pressure air fiom the lower
surface leaks through the gap and energizes the retarded upper surface boundary
cl
REVIEW OF BASIC AERODYNAMIC PRINCIPLES               25
Cl, max
flg.l 25    Schematic -variation oflift coefficient for airfoils with and without flaps.
High Energy Flow
Fig.1.26   Schematicillustration offlow around a slotted trailing-edge flap.
  \\--
26               PERFORMANCE, STABILITY, DYNAMICS, AND CONTROL
layer. This process helps to delay the fiow separation on the upper surface and
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：PERFORMANCE, STABILITY, DYNAMICS, AND CONTROL1(17)