曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

onto the mounting using the quick release.
(2) Install the mounting ball with the ends of the
lap straps with the central lock, or install
quick release.
(3) Install the seat shell. Refer to paragraph 2 above.
(4) Put the shoulder straps in position. And
install the attaching bolts. Or attach the
inertia reels with the 3 screws and install the
plastic covers
Equipment/Furnishings
DA20-C1 AMM
Page 204
24 Mar 1999 25-10-00 Doc # DA201-C1
Rev. 1
Figure 3: Baggage Compartment Floor Panel Installation
DA20-C1 AMM
Equipment/Furnishings
Doc # DA201-C1
Rev. 9 25-10-00 Page 205
29 Apr 2004
4. Remove/Install the Instrument Panel Cover
A. Remove the Instrument Panel Cover
Detail Steps/Work Items Key Items
(1) Remove the screws around the edge of the
instrument panel cover.
(2) Lift the cover clear.
B. Install the Instrument Panel Cover
Detail Steps/Work Items Key Items
(1) Make sure that there are no unwanted items
forward of the instrument panel.
(2) Put the instrument panel cover in position.
(3) Install the screws around the edge of the
cover.
Install the screws to the instrument panel
first. Then install the screws to the
fuselage.
5. Remove/Install the Baggage Compartment Floor Panel
A. Remove the Baggage Compartment Floor Panel. (Refer to Figure 3)
Detail Steps/Work Items Key Items
(1) Remove the battery box cover. (Aircraft with
aft mounted battery only).
(2) Remove inertia reel covers, if fitted.
(3) Remove the screws around the aft edge of
the center floor panel.
(4) Remove the screws along the joints for the
left and right panels.
(5) Remove the fuel dip-stick from the clips.
(6) Remove the screws along the front edge of
the center panel.
Note the location of the baggage net and
the gripper clips for the dip-stick.
(7) Lift the center panel clear.
(8) If necessary, remove the screws from the
outer edges of the outer panels.
Only remove the outer panels if necessary.
(9) Lift the outer panel clear.
Equipment/Furnishings
DA20-C1 AMM
Page 206
29 Apr 2004 25-10-00 Doc # DA201-C1
Rev. 9
B. Install the Baggage Compartment Floor Panel. (Refer to Figure 3)
Detail Steps/Work Items Key Items
(1) Make sure that there are no unwanted items
in below the floor panel.
(2) If necessary, put the outer floor panels in
position.
Only if the panels were removed.
(3) Install the screws around the edge of the
outer panels.
(4) Put the center floor panel in position.
(5) Loosely install the screws along the forward
edge of the panel.
Each screw attaches the baggage net.
Two screws also attach the clips for the
dip-stick.
(6) Loosely install the screws along the joints of
the left and right panels and the center
panel.
(7) Loosely install the screws along the aft edge
of the center panel.
(8) Install inertia reel covers, if fitted.
(9) Install the battery box cover. (Aircraft with
aft mounted batteries only)
(10) Tighten all of the screws.
6. Cleaning
A. Seats
The seat cushions are a fire resistant material. Clean the cushions with a vacuum cleaner. Use
a mild soap solution to remove stains.
B. Safety Belts
Use a mild soap solution to remove dirt from the safety belts.
DA20-C1 AMM
Equipment/Furnishings
Doc # DA201-C1
Rev. 0 25-60-00 Page 1
19 Dec 1997
CHAPTER 25-60
EMERGENCY
1. General
This Section tells you about the optional Emergency Location Transmitter (ELT). It tells you only
about the installation in the airplane. See the manufacturers Operator’s Manual for more data.
2. Description
The ELT is located in a compartment in the B-bulkhead behind the right seat. The ELT transmits a
signal automatically after a crash on the emergency frequencies of 121.5 and 243.0 MHz. You can
operate the ELT manually for testing (or after an emergency landing).
Maintenance on the airplane is only a visual examination of the installation (housing, mounting and
antenna). Monitor the battery expiry date. The date is on the identification plate on the housing.
Replace batteries when they expire or after 1 hour of cumulative use.
Do regular functional tests (See the Flight Manual).
Equipment/Furnishings
DA20-C1 AMM
Page 2
19 Dec 1997 25-60-00 Doc # DA201-C1
Rev. 0
Figure 1: ELT Installation
DA20-C1 AMM
Equipment/Furnishings
Doc # DA201-C1
Rev. 0 25-60-00 Page 201
19 Dec 1997
MAINTENANCE PRACTICES
1. General
This part tells you only how to test the ELT in the airplane. See the ELT manufacturers Operator’s
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石20系列AMM 1(88)