曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

13772-130 49 of 58
Cirrus Design Section 9
SR22 Supplements
Section 7 - Systems Description
Airframe
Wings
The wing structure is constructed of composite materials producing
wing surfaces that are smooth and seamless. The wing cross section
is a blend of several high performance airfoils. A high aspect ratio
results in low drag. Each wing provides attach structure for the main
landing gear and contains a 47.25-gallon fuel tank.
The G3 Wing is constructed in a conventional spar, rib, and shear
section arrangement. The upper and lower skins are bonded to the
spar, ribs, and aft shear web forming a torsion box that carries all of
the wing bending and torsion loads. The rear shear webs are similar in
construction but do not carry through the fuselage. The main spar is
laminated epoxy/carbon fiber in a C-section, and is continuous from
wing tip to wing tip. The wing spar passes under the fuselage below
the two front seats and is attached to the fuselage in two locations. Lift
and landing loads are carried by the single carry-through spar, plus a
pair of rear shear webs (one on each wing) attached to the fuselage.
Rudder System
G3 Wing geometry is slightly changed with an increase in dihedral of
1° which allows for the elimination of the aileron-rudder interconnect
system.
Revision 02: 08-26-09
50 of 58 13772-130
Section 9 Cirrus Design
Supplements SR22
Fuel System
An 92-gallon usable wet-wing fuel storage system provides fuel for
engine operation. The system consists of a 47.25-gallon capacity (46-
gallon usable) vented integral fuel tank and a fuel collector/sump in
each wing, a three position selector valve, an electric boost pump, and
an engine-driven fuel pump. Fuel is gravity fed from each tank to the
associated collector sumps where the engine-driven fuel pump draws
fuel through a filter and selector valve to pressure feed the engine fuel
injection system. The electric boost pump is provided for engine
priming and vapor suppression.
Each integral wing fuel tank has a filler cap in the upper surface of
each wing for fuel servicing. Access panels in the lower surface of
each wing allow access to the associated wet compartment (tank) for
inspection and maintenance. Float-type fuel quantity sensors in each
wing tank supply fuel level information to the fuel quantity indicators.
Positive pressure in the tank is maintained through a vent line from
each wing tank. Fuel, from each wing tank, gravity feeds through
strainers and a flapper valve to the associated collector tank in each
wing. Each collector tank/sump incorporates a flush mounted fuel
drain and a vent to the associated fuel tank.
The engine-driven fuel pump pulls filtered fuel from the two collector
tanks through a three-position (LEFT-RIGHT-OFF) selector valve. The
selector valve allows tank selection. From the fuel pump, the fuel is
metered to a flow divider, and delivered to the individual cylinders.
Excess fuel is returned to the selected tank.
A dual-reading fuel-quantity indicator is located in the center console
next to the fuel selector in plain view of the pilot. Fuel shutoff and tank
selection is positioned nearby for easy access.
Fuel system venting is essential to system operation. Blockage of the
system will result in decreasing fuel flow and eventual engine fuel
starvation and stoppage. Venting is accomplished independently from
each tank by a vent line leading to a NACA-type vent mounted in an
access panel underneath the wing near each wing tip.
The airplane may be serviced to a reduced capacity to permit heavier
cabin loadings. This is accomplished by filling each tank to a tab
visible below the fuel filler, giving a reduced fuel load of 30.0 gallons
usable in each tank (60 gallons total usable in all flight conditions).
Revision 02: 08-26-09
13772-130 51 of 58
Cirrus Design Section 9
SR22 Supplements
Drain valves at the system low points allow draining the system for
maintenance and for examination of fuel in the system for
contamination and grade. The fuel must be sampled prior to each
flight. A sampler cup is provided to drain a small amount of fuel from
the wing tank drains, the collector tank drains, and the gascolator
drain. If takeoff weight limitations for the next flight permit, the fuel
tanks should be filled after each flight to prevent condensation.
Fuel Quantity Indicator
A dual reading 2¼” fuel quantity indicator is installed on the console
immediately forward of the fuel selector valve. The LEFT pointer
indicates left tank fuel quantity and sweeps a scale marked from 0 to
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：CIRRUS DESIGN SR22西銳22飛行員操作手冊和飛機飛行手冊(150)