曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

through the engine. The amount of damage will vary and may
not become evident for many hours. However, the engine may
be severely damaged and may fail shortly following application
of high power. Proper procedures require thorough application
of preheat to all parts of the engine. Hot air must be applied
directly to the oil sump and external oil lines as well as the
Revision A5
4-26 P/N 13772-001
Section 4 Cirrus Design
Normal Procedures SR22
cylinders, air intake and oil cooler. Because excessively hot air
can damage non-metallic components such as composite
parts, seals, hoses, and drives belts, do not attempt to hasten
the preheat process.
1. Ignition Switch ..........................................................................OFF
• WARNING •
Use extreme caution when pulling the propeller through by
hand. Make sure ignition switch is OFF, keys are out of
ignition, and then act as if the engine will start. A loose or
broken ground wire on either magneto could cause the engine
to fire.
2. Propeller........................................... Hand TURN several rotations
3. External Power (If applicable) .......................................CONNECT
4. Brakes ..................................................................................HOLD
5. Bat Master Switches ........................................ ON (check voltage)
6. Mixture ......................................................................... FULL RICH
7. Power lever..........................................................FULL FORWARD
8. Fuel Pump.....................................................PRIME, then BOOST
• Note •
Serials 0002 - 0278 before SB 22-73-01: In temperatures
down to 20°F, hold Fuel Pump switch to PRIME for 60-120
seconds prior to starting.
Serials 0002 - 0278 after SB 22-73-01 and 0279 and
subsequent: In temperatures down to 20°F, hold Fuel Pump
switch to PRIME for 15 seconds prior to starting.
9. Propeller Area .....................................................................CLEAR
10. Power Lever ............................................................OPEN ¼ INCH
(Continued on following page)
Revision A5
P/N 13772-001 4-27
Cirrus Design Section 4
SR22 Normal Procedures
11. Ignition Switch....................... START (Release after engine starts)
• Caution •
Limit cranking to intervals of 20 seconds with a 20 second
cooling period between cranks. This will improve battery and
contactor life
12. Power Lever ...............................RETARD (to maintain 1000 RPM)
13. Oil Pressure ....................................................................... CHECK
14. Alt Master Switches ...................................................................ON
15. Avionics Power Switch ...............................................................ON
16. Engine Parameters ........................................................MONITOR
17. External Power (If applicable) ................................. DISCONNECT
18. Amp Meter/Indication......................................................... CHECK
19. Strobe Lights..............................................................................ON
Hot Weather Operation
Avoid prolonged engine operation on the ground.
• Note •
Fuel BOOST must be ON for engine start and takeoff, and
should be ON during climb for vapor suppression which could
occur under hot ambient conditions or after extended idle.
Revision A5
4-28 P/N 13772-001
Section 4 Cirrus Design
Normal Procedures SR22
Noise Characteristics/Abatement
The certificated noise levels for the Cirrus Design SR22 established in
accordance with FAR 36 Appendix G are:
No determination has been made by the Federal Aviation
Administration that the noise levels of this airplane are or should be
acceptable or unacceptable for operation at, into, or out of, any airport.
The above noise levels were established at 3400 pounds takeoff
weight and 2700 RPM.
Recently, increased emphasis on improving environmental quality
requires all pilots to minimize the effect of airplane noise on the public.
The following suggested procedures minimize environmental noise
when operating the SR22.
• Note •
Do not follow these noise abatement procedures where they
conflict with Air Traffic Control clearances or instructions,
weather considerations, or wherever they would reduce safety.
1. When operating VFR over noise-sensitive areas, such as outdoor
events, parks, and recreational areas, fly not less than 2000 feet
above the surface even though flight at a lower level may be
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：CIRRUS DESIGN SR22西銳22飛行員操作手冊和飛機飛行手冊(38)