曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

P/N 13772-001 4-15
Cirrus Design Section 4
SR22 Normal Procedures
to extinguish ALT 2 caution light. ALT 2 caution light should go
out below 2200 RPM.
16. Voltage............................................................................... CHECK
17. Pitot Heat ............................................................... AS REQUIRED
• Note •
Pitot Heat should be turned ON for flight into IMC, flight into
visible moisture, or whenever ambient temperatures are 41° F
(5° C) or less.
18. Navigation Lights ................................................... AS REQUIRED
19. Landing Light ......................................................... AS REQUIRED
20. Magnetos ....................................................CHECK Left and Right
a. Ignition Switch ..................................R, note RPM, then BOTH
b. Ignition Switch .................................. L, note RPM, then BOTH
• Note •
RPM drop must not exceed 150 RPM for either magneto. RPM
differential must not exceed 75 RPM between magnetos. If
there is a doubt concerning operation of the ignition system,
RPM checks at higher engine speeds will usually confirm
whether a deficiency exists.
An absence of RPM drop may indicate faulty grounding of one
side of the ignition system or magneto timing set in advance of
the specified setting.
21. Engine Parameters ............................................................ CHECK
22. Power Lever ................................................................... 1000 RPM
23. Flight Instruments, HSI, and Altimeter ....................CHECK & SET
24. Flight Controls................................................. FREE & CORRECT
25. Trim..............................................................................SET Takeoff
26. Autopilot .................................................................. DISCONNECT
Revision A9
4-16 P/N 13772-001
Section 4 Cirrus Design
Normal Procedures SR22
Maximum Power Fuel Flow
Leaning for Takeoff and Maximum Climb is accomplished at full throttle
by leaning the mixture from full rich to the target fuel flow for the given
pressure altitude. The fuel flow values in the table below were
demonstrated to obtain the takeoff and climb performance presented
in Section 5.
• Note •
Excessively rich mixture will occur if the Mixture control is set to FULL
RICH above 7500 feet pressure altitude.
Pressure
Altitude
Target
Fuel Flow
Pressure
Altitude
Target
Fuel Flow
Pressure
Altitude
Target Fuel
Flow
0 27.1 7000 21.4 14,000 17.5
1000 26.2 8000 20.5 15,000 16.9
2000 25.1 9000 19.9 16,000 16.7
3000 24.3 10,000 19.5 17,000 16.2
4000 23.6 11,000 18.8 17,500 16.1
5000 22.8 12,000 18.4
6000 22.1 13,000 17.9
Revision A5
P/N 13772-001 4-17
Cirrus Design Section 4
SR22 Normal Procedures
Takeoff
Power Check: Check full-throttle engine operation early in takeoff run.
The engine should run smoothly and turn approximately 2700 RPM.
All engine parameters should read in the green. Discontinue takeoff at
any sign of rough operation or sluggish acceleration. Make a thorough
full-throttle static run-up before attempting another takeoff.
For takeoff over a gravel surface, advance Power Lever slowly. This
allows the airplane to start rolling before high RPM is developed, and
gravel will be blown behind the propeller rather than pulled into it.
Flap Settings: Normal and short field takeoffs are accomplished with
flaps set at 50%. Takeoffs using 0% are permissible, however, no
performance data is available for takeoffs in the flaps up configuration.
Takeoffs with 100% flaps are not approved.
Soft or rough field takeoffs are performed with 50% flaps by lifting the
airplane off the ground as soon as practical in a tail-low attitude. If no
obstacles are ahead, the airplane should be leveled off immediately to
accelerate to a higher climb speed.
Takeoffs into strong crosswinds are normally performed with the flaps
set at 50% to minimize the drift angle immediately after takeoff. With
the ailerons fully deflected into the wind, accelerate the airplane to a
speed slightly higher than normal while decreasing the aileron
deflection as speed increases then - with authority - rotate to prevent
possibly settling back to the runway while drifting. When clear of the
ground, make a coordinated turn into the wind to correct for drift.
• Note •
Fuel BOOST should be left ON during takeoff and for climb as
required for vapor suppression with hot or warm fuel.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：CIRRUS DESIGN SR22西銳22飛行員操作手冊和飛機飛行手冊(34)