曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

PRE-FLT OBC Displayed when the preflight OBC test sequence is completed. Message is
COMPLETE displayed if sequence completes normally or is terminated, or if interlock
conditions change.
IN-FLT OBC COMPLETE Displayed when the in-flight OBC test sequence is completed. Message is
displayed if sequence completes normally or is terminated, or if interlock
conditions change.
3ETEST COMPLETE Displayed when the retest OBC sequence is completed. Message is displayed if
sequence completes normally or is terminated, or if interlock conditions change.
TEST COMPLETE
-<GROUP NAME>
Displayed when a functional group test is completed. Message is displayed if
group test completes normally or is terminated, or if interlock conditions change.
<GROUP NAME> appears as AUX, CD, CNI, FLT, NAV, EW, TAC, or IRST for
the functional group that completed test.
3BC SEQ ABORTED Displayed when an OBC sequence (preflight or in-flight) is terminated through
the OBC BASIC format while it is in progress.
%ETEST ABORTED Displayed when a retest sequence is terminated through the OBC BASIC format
while it is in progress.
‘ILOT OBC DISABLE Displayed when the Pilot’s MASTER TEST panel switch remains in OBC 10
seconds after commended BIT completes for an equipment that required this
interlock to initiate test.
NTERLOCK ABORT Displayed when an interlock condition changes state (i.e., no longer satisfied)
for an equipment that is already in test. Commanded BIT will be terminated for
the affected equipment.
ZHALLENGE IFF Displayed when the IFF Interrogator has not been challenged prior to the
selection of a test sequence. This message is displayed only once at the time of
the test sequence selection. If the system cold starts, or SYSTEM RESET is
pressed, this message will be displayed again when a test sequence selection is
made.
NVALID <WRA NAME>
.OAD
Displayed when an equipment has an inconsistent firmware load, or is not
compatible with the mission computer software load. The <WRA NAME> field
applies to the following equipments: MCI, MC2, CIU, SAHR, MD%, MDS2,
DEU, INS, ADAC, SMS, RWR, ASPJ, RDR, SDIS, IRS-T
Figure 38-12. OBC Computer Messages
38-29 ORIGINAL
NAVAIR 01.Fl4AAD-1
OBC/CSS MESSAGE
JOW NOT SATISFIED
DESCRIPTION
Displayed when equipment is selected for test via a unit, inffight, or preflight
test selection, and the WOW (Weight-on/off-Wheel) interlock condition is
not satisfied. Testing will not be initiated for the selected equipment. Note that
this message will not be displayed for functional group or retest test
selections.
AS NOT SATISFIED Displayed when equipment is selected for test via a unit, inflight, or preflight
test selection, and the TAS (True Air Speed interlock condition less than or
greater than 76 knots) is not satisfied. Testing will not be initiated for the
selected equipment. Note that this message will not be displayed for
functional group or retest selections.
1ULTI INTLK NOT MET Displayed when equipment is selected for test via a unit, inflight or preflight
test selection, and more than one (i.e., multiple) interlock conditions are not
satisfied (WOW, TAS, PARKING BRAKE, or MTP). Testing will not be initiated
for the selected equipment. Note that this message will not be displayed for
functional group or retest selections.
,QlJlPMENT CONFLICT Displayed when equipment is selected for teti whidr conflicts with other
equipment already in test. These conflicts are primarily between equipments
subordinate to the CIU, between CIU subordinate equipment and the CIU
itsetf, between DPI and DP2, and between MC1 and MC2. Testing will not be
initiated for equipment that conflict operationally.
IO COMMANDED BIT Displayed when equipment that does not support command BIT is selected
for test.
IBC SEQ IN PROGRESS Displayed when equipment is selected for test that is the same as equipment
already in test as part of an OBC inflight or preflight test sequence. Testing for
the selected equipment will not be initiated.
ETEST IN PROGRESS Displayed when equipment is selected for test that is the same as equipment
already in test as part of an OBC RETEST sequence. Testing for the selected
equipment will not be initiated.
IASTER TEST NOT SET Displayed when equipment is selected for test through a unit or preflight test
selection and the pilot’s MASTER TEST panel switch is not set to OBC. This
message is displayed as long as an OBC or CSS format is presented, and
removed when the switch is set to OBC.
IANDBRAKE NOT SET Displayed when equipment is selected for test via a unit or preflight test
sequence selection and the handbrake is not set. This message is
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：F-14D 飛行手冊 Flight Manual 3(72)