(2) Lateral axis YY: Perpendicular to the axis XX and parallel to the line made by the points 20L and 20R.
 (3) Vertical axis ZZ: perpendicular to the axes XX and YY.
 Subtask 08-22-00-582-050

 C. Aircraft Lifting CAUTION : YOU MUST NOT LIFT THE AIRCRAFT WITH THE SAFETY STAY.
_______
 (1) Lift the aircraft on the jacks (Ref. TASK 07-11-00-581-001) NOTE : Do not put the safety stay in position before you make the
____
 aircraft level.

 Subtask 08-22-00-480-050
 D. Put the Sighting Rods and the Sight Tube in Position
 (1)
 Put the sighting rods SIGHTING RODS SET (98D08103500106) and (98D08103500107) at points 2L and 2R on the wing lower surface.

 (2)
 Put the sighting rods SIGHTING RODS SET (98D08103500101) and (98D08103500102) at points 11 and 12 under the fuselage.

 (3)
 Put the sight tube in position near the aircraft. The sight point is located on the Z axis at -3500 mm (-137.7953 in.) from the datum plane. (Ref. Fig. 202/TASK 08-22-00-991-002)

 4. Procedure
_________
 Subtask 08-22-00-210-050

 A. Aircraft Leveling R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 (Ref. Fig. 203/TASK 08-22-00-991-003)
 **ON A/C 301-399,

 (Ref. Fig. 203A/TASK 08-22-00-991-003-A)
 EFF : ALL  08-22-00Page 205   Aug 01/05   CES

 Location of the Sight Tube Figure 202/TASK 08-22-00-991-002
 EFF :  R CES  ALL     08-22-00 Page 206 May 01/04

 Transverse and Longitudinal Alignment
 Figure 203/TASK 08-22-00-991-003

R EFF : 001-049, 051-099, 101-149, 151-199,  08-22-00Page 207 201-299, 401-499, Aug 01/05   CES

R  Transverse Alignment 
R  Figure 203A/TASK 08-22-00-991-003-A
 EFF :  301-399,    08-22-00 Page 208 
    May 01/04
   
 CES  

R **ON A/C ALL
 (1)
 Operate the hydraulic jacks installed at RIB8 to align points 2L and 2R with the sight tube. You get the tranverse alignment.

 (2)
 Operate the hydraulic jacks installed at FR8 to align points 11 and 12 with the sight tube. You get the longitudinal alignment.

 (3)
 When you have done the longitudinal alignment, do a check of the transverse alignment.

 (4)
 Put the safety stay in position between FR73 an FR74.

 5. Close-up
________
 Subtask 08-22-00-410-050

 A. Close Access
 (1)
 Remove the sighting rods.

 (2)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 (3) Remove the access platform(s).
 Subtask 08-22-00-586-050

 B. Aircraft Lowering
 (1) Lower the aircraft (Ref. TASK 07-11-00-586-002).
 EFF : ALL  08-22-00Page 209   May 01/04   CES