(a) Release the fasteners of the panel (1) and disengage the panel

 (1) from its housing.

 (b) Disconnect the connector (3) from the panel (1).

 (c) Remove the panel (1).

 (d) Put blanking caps on the connectors (2) and (3).

 (7) Remove the screws (14).

 (8) Remove the ventilation plates (15).

 (9) Disconnect the clamps (16).

 (10) Remove the screws (10) and the washers (11).
 (Ref. Fig. 503/TASK 76-11-00-991-912)

 (11) Remove the plates (12) and (13).

 (12) Cut and remove the lockwire and adjust the length of the adjustable rod (6) (Ref. Fig. 501/TASK 76-11-00-991-910) detail B.

 (13) Tighten and safety the hinge points and the adjustable rod ends with lockwire 0.032 in. (0.8 mm) dia..

 Subtask 76-11-00-869-061
 C. With the throttle control lever in the IDLE STOP position, make sure that you can :
 (1) Easily install the pin (5) in the artificial feel unit (1)

 (2) Easily remove this pin from the artificial feel unit (1)

 (3) Install the pin again.

 F 『 EEFF : ALL E Page 50576-11-00
 E E Feb 01/98 E E ECES E

 Panels 111VU and 112VU
 Figure 502/TASK 76-11-00-991-911

 F 『 EEFF : ALL E Page 50676-11-00
 E E Feb 01/98 E E ECES E

 Ventilation Plates and Clamps
 Figure 503/TASK 76-11-00-991-912

 F 『 EEFF : ALL E Page 50776-11-00
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (4) Make sure that you can:

 (a) Easily install the RIGGING PIN (98DNSA20206080) (3) in the throttle control unit (4) and in the input lever,

 (b) Easily remove this pin from these components.

 (c) If you can not do this, adjust the length of the rod (2).
 Subtask 76-11-00-820-057

 D. Cut and remove the lockwire and adjust the length of the adjustable rod (2). (Ref. Fig. 501/TASK 76-11-00-991-910) detail B.
 (1) Disconnect the rod (2) from the throttle control unit and the artificial feel unit to install the lockwire 0.032 in. (0.8mm) dia.. Tighten and safety the hinge points and the adjustable rod ends.

 (2) Install the rod (2).
 Subtask 76-11-00-869-062

 E. Remove the pin (5). With the throttle control lever in the IDLE STOP position make sure that you can :
 (1) Easily remove the pin (3) from the throttle control unit.

 (2) Easily install this pin in this unit. Remove this pin.

 5. Close-up
________
 Subtask 76-11-00-869-063

 A. Make sure that all the pins are removed.
 (1) Install the plates (12) and (13).

 (2) Install the screws (10) and washers (11).

 (3) Install the clamps (16).

 (4) Install the ventilation plates (15).

 (5) Install the screws (14).

 F 『 EEFF : ALL E Page 50876-11-00
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (6) Install the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU. (Ref. Fig. 502/TASK 76-11-00-991-911)
 NOTE : The installation procedure is the same for the FLOOD LT/INTEG
____ LT panel 111VU and FLOOD LT panel 112VU.
 (a) Remove the blanking caps from the connectors (2) and (3).

 (b) Install the connector (2) on the panel (1).

 (c) Install the panel (1) on the structure.

 (d) Fully tighten the fasteners on the panel (1).

 (7) Install the Multipurpose Control and Display Units (3CA1 and 3CA2). (Ref. TASK 22-82-12-400-002)

 (8) Install the Radio Management Panels (1RG1 and 1RG2) (Ref. TASK 23-13-13-400-001)

 (9) Install the Audio Control Panels (2RN1 and 2RN2) (Ref. TASK 23-51-12-400-001)

 (10) Install the Weather Radar Control Unit (3SQ) (Ref. TASK 34-41-12-400-001)

 (11) Install the ATC/TCAS Control Unit (3SH) (Ref. TASK 34-52-12-400-001)

 (12) Make sure that the work area is clean and clear of tool(s) and other items.

 Subtask 76-11-00-410-055
 B. Close Access
 (1) Close the access door 811.

 (2) Remove the access platform(s).

 (3) Remove the warning notice(s).
 Subtask 76-11-00-865-060

 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1JH, 2JH1, 2JH2, 3JH1, 3JH2, 21CE1, 21CE2, 22CE, 21CE3.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE CONTROLS 發動機控制(6)