- the throttle control levers
- the slat and flap control levers.
(2) On the panel 50VU:
- Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
- Install a warning notice.
(3) On the panel 115VU:
- Put a warning notice to tell persons not to start the engine 1(2).
F 『 EEFF : ALL E Page 40276-11-17
E E Feb 01/99 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Subtask 76-11-17-010-052
D. Get Access
(1) Open the access door 811.
(2) Put an access platform.
Subtask 76-11-17-010-055
E. Get Access
(1) Remove the Multipurpose Control and Display Units 3CA1 and 3CA2 (Ref. TASK 22-82-12-000-001).
(2) Remove the Radio Management Panels 1RG1 and 1RG2 (Ref. TASK 23-13-13-000-001).
(3) Remove the Audio Control Panels 2RN1 and 2RN2 (Ref. TASK 23-51-12-000-001).
(4) Remove the Weather Radar Control Unit 3SQ (Ref. TASK 34-41-12-000-001).
(5) Remove the ATC Control Unit 3SH (Ref. TASK 34-52-12-000-001).
(6) Remove the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU. (Ref. Fig. 401/TASK 76-11-17-991-908)
NOTE : The removal procedure is the same for the FLOOD LT/INTEG LT
____
panel 111VU and FLOOD LT panel 112VU.
(a) Release the fasteners of the panel (1) and disengage the panel
(1) from its housing.
(b) Disconnect the connector (3) from the panel (1).
(c) Remove the panel (1).
(d) Put blanking caps on the connectors (2) and (3).
(7) Remove the screws (7).
(8) Remove the ventilation plates (8).
(9) Disconnect the clamps (9).
F 『 EEFF : ALL E Page 40376-11-17
E E Feb 01/98 E E ECES E
Panels 111 and 112VU
Figure 401/TASK 76-11-17-991-908
F 『 EEFF : ALL E Page 40476-11-17
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(10) Remove the screws (6) and the washers (5).
(Ref. Fig. 402/TASK 76-11-17-991-909)
(11) Remove the plates (4) and (10).
4. Procedure
_________ Subtask 76-11-17-480-052
A. Install the RIGGING PIN (98DNSA20206080) (11) in the throttle control unit (Ref. Fig. 402/TASK 76-11-17-991-909)
Subtask 76-11-17-020-051
B. Remove the Throttle Control Artificial Feel Unit as follows:
(1) Remove and discard the 4 cotter pins (13)
(Ref. Fig. 403/TASK 76-11-17-991-910)
(2) Remove the 4 nuts (14), the 4 washers (15) and the 4 bolts (17). Make sure that the 4 bushes (16) stay bonded.
(3) Remove the rods (27).
(4) Remove and discard the 4 cotter pins (18).
(5) Remove the 2 nuts (19), the 2 washers (20) and the 2 bolts (26). Make sure that the 2 bushes (25) stay bonded.
(6) Remove the 2 nuts (21), the 2 washers (22) and the 2 bolts (24).
(7) Remove the throttle control artificial feel unit (23).
F 『 EEFF : ALL E Page 40576-11-17
E E Feb 01/98 E E ECES E
Ventilation Plates and Clamps
Figure 402/TASK 76-11-17-991-909
F 『 EEFF : ALL E Page 40676-11-17
E E Feb 01/98 E E ECES E
Throttle Control Rigging
Figure 403/TASK 76-11-17-991-910
F 『 EEFF : ALL E Page 40776-11-17
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 76-11-17-400-042
Installation of the Throttle Control Feel Unit
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 1.8 m (5 ft. 11 in.)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE CONTROLS 發動機控制(9)
