R R Main Junction Box Figure 403/TASK 77-21-10-991-305- 13 (SHEET 1)
F EEFF : E E ECES ALL 『E 77-21-10EEE Page 426 Aug 01/04
R R Main Junction Box Figure 403/TASK 77-21-10-991-305- 23 (SHEET 2)
F EEFF : E E ECES ALL 『E 77-21-10EEE Page 427 Aug 01/04
R R Main Junction Box Figure 403/TASK 77-21-10-991-305- 33 (SHEET 3)
F EEFF : E E ECES ALL 『E 77-21-10EEE Page 428 Aug 01/04
F 『
E C F M E
E E
E 56-5B E
E E
TASK 77-21-10-400-025
R Installation of the Main Junction Box
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific warning notice No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2101 USA MIL-T-5544
graphite grease (Ref. 70-30-00)
Material No. CP8001 *
lockwire 0.032 in (0.8 mm) dia (Ref. 70-30-00)
Material No. CP8002 *
lockwire 0.032 in (0.8 mm) dia (Ref. 70-30-00)
F 『 EEFF : ALL E Page 42977-21-10
E E Aug 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 31-60-00-860-001 EIS Start Procedure
R 31-60-00-860-002 EIS Stop Procedure 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine Non motoring)
78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-36-00-010-040 Opening of the Thrust Reverser Doors
78-36-00-410-040 Closing of the Thrust Reverser Doors
R 77-21-10-991-305 Fig. 403
3. Job Set-up
__________
Subtask 77-21-10-860-059
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
Subtask 77-21-10-010-085
B. Get Access
(1) Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
F 『 EEFF : ALL E Page 43077-21-10
E E Aug 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(2) Make sure that the thrust reverser doors are open: (Ref. TASK 78-36-00-010-040) FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 77-21-10-040-069
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
4. Procedure
_________
R (Ref. Fig. 403/TASK 77-21-10-991-305)
Subtask 77-21-10-420-059
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE INDICATING 發動機指示(21)
