TRF Vibration Sensor
 Figure 401/TASK 77-31-30-991-302- 33 (SHEET 3)
 F EEFF :  ALL  『E 77-31-30 Page 406 
E  E  Feb 01/98
 E  E
 ECES  E

 (7) Put blanking caps on the disconnected electrical connectors.
 F 『 EEFF : ALL E Page 40777-31-30
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 77-31-30-400-002
 Installation of the Turbine Rear Frame Vibration Sensor
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 1.5 m (4 ft. 11 in.)
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in
R (0.05 to 0.40 m.daN) No specific Torque Wrench : range 36.00 to 220.00 lbf.in
 (0.40 to 2.60 m.daN)
 No specific Torque Wrench : range 96.00 to 900.00 lbf.in

 (1.00 to 10.00 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
Material No. CP2101 USA MIL-T-5544
 Graphite Grease (Ref. 70-30-00)
 Material No. CP8004 *
 lockwire 0.024in. (0.6 mm) dia. (Ref. 70-30-00)
 Material No. CP8005 *
 Lockwire 0.024in. (0.6 mm) dia. (Ref. 70-30-00)

 F 『 EEFF : ALL E Page 40877-31-30
 E E May 01/05 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-00-00-710-003 Engine Automatic Start 71-00-00-710-028 Engine Shutdown 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 77-32-34-860-041 Change the configuration of the Accelerometer 78-30-00-081-041 Make the Thrust Reverser Serviceable after
 Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors 77-31-30-991-302 Fig. 401
 3. Job Set-up
__________
 Subtask 77-31-30-860-051
 A. Aircraft Maintenance Configuration
 (1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.

 (2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).

 (3) Make sure that the access platform is in position.

 Subtask 77-31-30-010-059
 B. Get Access
 (1) Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
 F 『 EEFF : ALL E Page 40977-31-30
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (2) Make sure that the left thrust reverser door is open: (Ref. TASK 78-36-00-010-040) FOR 1000EM1 451AL FOR 1000EM2 461AL
 Subtask 77-31-30-040-057
 C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
 4. Procedure
_________
 (Ref. Fig. 401/TASK 77-31-30-991-302) Subtask 77-31-30-420-051
 A. Installation of the TRF Vibration Sensor
 (1) Remove the blanking caps from the electrical connectors.

 (2) Install the bracket (30) on the connector (20) as follows (Ref. Detail B):

 (a) Lubricate threads of screws (10) with Graphite Grease (Material No. CP2101).

 (b) Attach the bracket (30) to the connector (20) with half-plates

 (60) and screws (10).

 (c) TORQUE the screws (10) to between 9.5 and 10.5 lbf.in (0.10 and
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE INDICATING 發動機指示(52)