- after 5 minutes, open and close circuit breaker 5DG1 to do a reset of the WHC1.
 (a) If the fault continues:
 - refer to Para. C.

 (2) If the WHC1 PN 6664287 is not installed:

 - refer to Para. C.
 **ON A/C 215-220, 224-224,
 C. If the test gives the maintenance message L FIXED WINDOW SENSOR:
 - disconnect the connector from the L fixed window (7DG1) and do a check of the resistance between pins A/C and A/D. (Ref. Fig. 202/TASK 30-42-00-991-007, 206/TASK 30-42-00-991-005)
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 234
 Aug 01/05R
 CES

 L Fixed Window Electrical Connector
 Figure 206/TASK 30-42-00-991-005

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 235
 201-299, Aug 01/05 CES

 (1) If the resistance is more than 715 ohms (open circuit) (OAT more than 40 deg. C) or is less than 370 ohms (short circuit):

 - do a check of the resistance of the spare sensor between pins A/E and A/F for correct value. (Ref. Fig. 202/TASK 30-42-00-991-007)
 (a) If the resistance of the spare sensor is between 370 ohms and 715 ohms:

 - connect pins B/U and B/V of the WHC1 (2DG1) to pins A/E and A/F of the spare sensor (Ref. AWM 30-42-03) and (Ref. ASM 30-42/01).

 (b) If the resistance of the spare sensor is more than 715 ohms or less than 370 ohms:

 - replace the WINDOW-FIXED, L (7DG1), (Ref. AMM TASK 56-11-12-000-001) and (Ref. AMM TASK 56-11-12-400-002).

 (c) If the fault continues:

 - replace the WHC-1 (2DG1), (Ref. AMM TASK 30-42-34-000-001) and (Ref. AMM TASK 30-42-34-400-001).

 (d) If the fault continues:

 - do a check and repair the wiring from the WHC 1 (2DG1) to the L fixed window (7DG1) pins B/U and B/V to pins A/D and A/C and pins B/U and B/V to pins A/E and A/F.

 (2) If the resistance is between 370 ohms and 715 ohms:

 (a) Replace the WHC-1 (2DG1), (Ref. AMM TASK 30-42-34-000-001) and (Ref. AMM TASK 30-42-34-400-001).

 (b) If the fault continues:

 - do a check and repair the wiring from the WHC 1 (2DG1) to the L fixed window (7DG1) pins B/U and B/V to pins A/D and A/C and pins B/U and B/V to pins A/E and A/F.
R **ON A/C 301-399, 401-499,

R C. If the test gives the maintenance message L FIXED WINDOW SENSOR
R associated with ECAM message ANTI-ICE L WINDSHIELD, or ANTI-ICE L WINDOW:
R - disconnect the connector from the L fixed window (7DG1) and do a check
R of the resistance between pins A/C and A/D.
R (Ref. Fig. 202/TASK 30-42-00-991-007, 206A/TASK 30-42-00-991-005-A)

R (1) If the resistance is more than 715 ohms (open circuit) (OAT more than
R 40 deg. C) or is less than 370 ohms (short circuit):
R - do a check of the resistance of the sensor 3 between pins A/D and
R A/E for correct value.
R (Ref. Fig. 202/TASK 30-42-00-991-007)

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 215-220, 224-224, 301-399, 401-499, ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 236
 Aug 01/05 CESR L Fixed Window Electrical Connector R Figure 206A/TASK 30-42-00-991-005-A

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 301-399, 401-499, ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 237
 Aug 01/05 CES

R (a) If the resistance of the sensor 3 is between 370 ohms and 715
R ohms:
R - connect pins B/U and B/V of the WHC1 (2DG1) to pins A/D and A/E
R of the sensor 3 (Ref. AWM 30-42-03) and (Ref. ASM 30-42/01).

R (b) If the resistance of the sensor 3 is more than 715 ohms or less
R than 370 ohms:
R - do a check of the resistance of the sensor 2 between pins A/E
R and A/F for correct value.
R (Ref. Fig. 202/TASK 30-42-00-991-007)

R 1_ If the resistance of the sensor 2 is between 370 ohms and 715
R ohms:
R - connect pins B/U and B/V of the WHC1 (2DG1) to pins A/E and
R A/F of the sensor 2 (Ref. AWM 30-42-03) and (Ref. ASM 30-R 42/01).

R 2_ If the resistance is more than 715 ohms and less than 370
R ohms:
R - replace the WINDOW-FIXED, L (7DG1), (Ref. AMM TASK 56-11-12-R 000-001) and (Ref. AMM TASK 56-11-12-400-002).