(2) If the resistance is between 370 ohms and 715 ohms:

 (a) Replace the WHC-2 (2DG2), (Ref. AMM TASK 30-42-34-000-001) and (Ref. AMM TASK 30-42-34-400-001).

 (b) If the fault continues:

 - do a check and repair the wiring from the WHC 2 (2DG2) to the R sliding window (8DG2) pins B/W and B/X to pins A/D and A/C and pins B/W and B/X to pins A/E and A/F.
R **ON A/C 301-399, 401-499,

R C. If the test gives the maintenance message R SLIDING WINDOW SENSOR
R associated with ECAM message ANTI-ICE R WINDSHIELD, or ANTI-ICE R WINDOW:
R - disconnect the connector from the R sliding window (8DG2) and do a
R check of the resistance between pin A/C and pin A/D.
R (Ref. Fig. 202/TASK 30-42-00-991-007, 209A/TASK 30-42-00-991-004-A)

R (1) If the resistance is more than 715 ohms (open circuit) (OAT more than
R 40 deg. C) or less than 370 ohms (short circuit):
R - do a check of the resistance of the sensor 3 between pins A/D and
R A/E for correct value.
R (Ref. Fig. 202/TASK 30-42-00-991-007)

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 215-220, 224-224, 301-399, 401-499, ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 255
 Aug 01/05 CESR R Sliding Window Electrical Connector R Figure 209A/TASK 30-42-00-991-004-A

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 301-399, 401-499, ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 256
 Aug 01/05 CES

R  (a) If the resistance of the sensor 3 is between 370 ohms and 715 
R  ohms: 
R  - connect pins B/W and B/X of the WHC2 (2DG2) to pins A/D and A/E 
R  of the sensor 3 (Ref. AWM 30-42-04) and (Ref. ASM 30-42/02). 
R  (b) If the resistance of the sensor 3 is more than 715 ohms or less 
R  than 370 ohms: 
R  - do a check of the resistance of the sensor 2 between pins A/E 
R  and A/F for correct value. 
R  (Ref. Fig. 202/TASK 30-42-00-991-007) 
R  1 If the resistance of the sensor 2 is between 370 ohms and 715_ 
R  ohms: 
R  - connect pins B/W and B/X of the WHC2 (2DG2) to pins A/E and 
R  A/F of the sensor 2 (Ref. AWM 30-42-03) and (Ref. ASM 30-
R  42/01). 
R  2 If the resistance is more than 715 ohms or less than 370 ohms:_ 
R  - replace the WINDOW-SLIDING, R (8DG2), (Ref. AMM TASK 56-12-
R  11-000-001) and (Ref. AMM TASK 56-12-11-400-001). 
R  3 If the fault continues:_ 
R  - replace the WHC-2 (2DG2), (Ref. AMM TASK 30-42-34-000-001) 
R  and (Ref. AMM TASK 30-42-34-400-001). 
R  4 If the fault continues:_ 
R  - do a check and repair the wiring from the WHC2 (2DG2) to the 
R  R sliding window (8DG2) pins B/W and B/X to pins A/D and A/C 
R  and pins B/W and B/X to pins A/D and A/E and pins B/W and 
R  B/X to pins A/E and A/F. 
R  (2) If the resistance is between 370 ohms and 715 ohms: 
R  (a) Replace the WHC-2 (2DG2), (Ref. AMM TASK 30-42-34-000-001) and 
R  (Ref. AMM TASK 30-42-34-400-001). 
R  (b) If the fault continues: 
R  - do a check and repair the wiring from the WHC2 (2DG2) to the R 
R  sliding window (8DG2) pins B/W and B/X to pins A/D and A/C and 
R  pins B/W and B/X to pins A/D and A/E and pins B/W and B/X to 
R  pins A/E and A/F. 
R  **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299,
 Post SB 30-1044 For A/C 215-220,224-224,
 C. If the test gives the maintenance message R SLIDING WINDOW SENSOR
 associated with ECAM message ANTI-ICE R WINDSHIELD, or ANTI-ICE R WINDOW:
 - disconnect the connector from the R sliding window (8DG2) and do a
 check of the resistance between pin A/C and pin A/D.
 (Ref. Fig. 209/TASK 30-42-00-991-004)

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞30-42-00∞∞∞∞∞∞∞∞∞∞Page 257
 Aug 01/05 CES

 (1) If the resistance is more than 715 ohms (open circuit) or less than 370 ohms (short circuit):

 - do a check of the resistance of the spare sensor between pins A/E and A/F for correct value. (Ref. Fig. 202/TASK 30-42-00-991-007)
 (a) If the resistance of the spare sensor is between 370 ohms and 715 ohms:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 除冰和排雨(73)