3. Fault Confirmation
__________________
A. Test Do the Interface test of the ADR (system 3) (Ref. AMM TASK 34-13-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message AOA SENSOR3 (3FP3)/ ADIRU3 (1FP3):
- replace the SENSOR-ANGLE OF ATTACK, 3 (3FP3) (Ref. AMM TASK 34-11-19-000-001) and (Ref. AMM TASK 34-11-19-400-001)
(1) If the fault continues:
- replace the ADIRU-3 (1FP3) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring from the angle of attack sensor 3 (3FP3) to the AOA INPUTS 1 and 2 of the ADIRU 3 (1FP3) (Ref. ASM 34-11/02).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A214
Feb 01/05R CES
R **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399, 401-499,
B. If the test is OK, reset the ADIRU (NAV-OFF-NAV) to clear the ECAM message. No other maintenance action is necessary.
**ON A/C ALL
C. Do the test given in Para. 3.
Loss of the TAT Sensor 1 Input on the ADR1
1. Possible Causes
_______________
- SENSOR-TAT, 1 (11FP1)
- ADIRU-1 (1FP1)
- wiring from the TAT sensor 1 to the ADIRU1
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
30-31-00-810-803 Loss of the GND/FLT Information (PHC 1)
AMM 30-31-00-710-001 Operational Test of the Probe Ice Protection
AMM 34-11-18-000-001 Removal of the TAT Sensor (11FP1, 11FP2)
AMM 34-11-18-400-001 Installation of the TAT Sensor (11FP1, 11FP2)
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-13-00-740-002 INTERFACE TEST of the ADR
ASM 34-11/02
3. Fault Confirmation
__________________
A. Test Do the Interface test of the ADR (system 1) (Ref. AMM TASK 34-13-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message TAT SENSOR (11FP1)/ ADIRU1 (1FP1):
- do the operational test of the probe ice protection (Ref. AMM TASK 30-31-00-710-001).
(1) If you cannot start the test:
- do the procedure that follows (Ref. TASK 30-31-00-810-803).
(2) If the test is OK:
- replace the SENSOR-TAT, 1 (11FP1) (Ref. AMM TASK 34-11-18-000-001) and (Ref. AMM TASK 34-11-18-400-001).
(a) If the fault continues:
- replace the ADIRU-1 (1FP1) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A216
Feb 01/05R CES
1 If the fault continues:
_
- do a check and repair the wiring from the TAT sensor 1 to the ADIRU1 (Ref. ASM 34-11/02).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A217
Feb 01/05R
CES Loss of the TAT Sensor 2 Input on the ADR2
1. Possible Causes
_______________
- SENSOR-TAT, 2 (11FP2)
- ADIRU-2 (1FP2)
- wiring from the TAT sensor 2 to the ADIRU2
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
30-31-00-810-803 Loss of the GND/FLT Information (PHC 1)
AMM 30-31-00-710-001 Operational Test of the Probe Ice Protection
AMM 34-11-18-000-001 Removal of the TAT Sensor (11FP1, 11FP2)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 1(90)
