3. Fault Confirmation
__________________
A. Test Do the Interface test of the ADR (system 2) (Ref. AMM TASK 34-13-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message TAT SENSOR (11FP2)/ ADIRU2 (1FP2):
- do the operational test of the probe ice protection (Ref. AMM TASK 30-31-00-710-001).
(1) If you cannot start the test:
- do the procedure that follows (Ref. TASK 30-31-00-810-803).
(2) If the test is OK:
- replace the SENSOR-TAT, 2 (11FP2) (Ref. AMM TASK 34-11-18-000-001) and (Ref. AMM TASK 34-11-18-400-001).
(a) If the fault continues:
- replace the ADIRU-2 (1FP2) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A218
Feb 01/05R CES
1 If the fault continues:
_
- do a check and repair the wiring from the TAT sensor 2 to the ADIRU2 (Ref. ASM 34-11/02).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A219
Feb 01/05R
CES Loss of the TAT Sensor 1 Input on the ADR3
1. Possible Causes
_______________
- SENSOR-TAT, 1 (11FP1)
- ADIRU-3 (1FP3)
- wiring from the TAT sensor 1 to the ADIRU3
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
30-31-00-810-803 Loss of the GND/FLT Information (PHC 1)
AMM 30-31-00-710-001 Operational Test of the Probe Ice Protection
AMM 34-11-18-000-001 Removal of the TAT Sensor (11FP1, 11FP2)
AMM 34-11-18-400-001 Installation of the TAT Sensor (11FP1, 11FP2)
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-13-00-740-002 INTERFACE TEST of the ADR
ASM 34-11/02
3. Fault Confirmation
__________________
A. Test Do the Interface test of the ADR (system 3) (Ref. AMM TASK 34-13-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message TAT SENSOR (11FP1)/ ADIRU3 (1FP3):
- do the operational test of the probe ice protection (Ref. AMM TASK 30-31-00-710-001).
(1) If you cannot start the test:
- do the procedure that follows (Ref. TASK 30-31-00-810-803).
(2) If the test is OK:
- replace the SENSOR-TAT, 1 (11FP1) (Ref. AMM TASK 34-11-18-000-001) and (Ref. AMM TASK 34-11-18-400-001).
(a) If the fault continues:
- replace the ADIRU-3 (1FP3) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A220
Feb 01/05R CES
1 If the fault continues:
_
- do a check and repair the wiring from the TAT sensor 1 to the ADIRU3 (Ref. ASM 34-11/02).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page A221
Feb 01/05R
CES Display of the Operational Message VMO/MMO..... 235/.60 on the Upper ECAM DU
1. Possible Causes
_______________
- wiring of the L/G DOWN VMO/MMO SELECTION switch (22FP)
- SW-L/G DOWN VMO/MMO SELECTION (22FP)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國(guó)航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 導(dǎo)航 NAVIGATION 1(91)
