- do a visual check of each connector for correct condition.
a If damage is found:
_ - repair or replace as required.
F 『 EEFF : ALL E ∞∞78-31-00∞∞∞∞∞∞∞∞∞∞Page 255
E E May 01/05 ERE
ECES (b) If the resistance values are in the specified limits:
F 『
E C F M E
E E
E 56 E
E E
b_ If nothing is found:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001)
and (Ref. AMM TASK 73-21-60-400-001).
- do a manual deployment of the thrust reverser blocker doors (Ref. AMM TASK 78-32-41-860-001)
- do a resistance check of the harnesses J5 and J6 (Ref. AWM 71-51-05) between: . pins 24 and 23 (>10 megohms) . pins 24 and 2 (<5 ohms) . pins 24 and 11 (>10 megohms) . pins 2 and 11 (>10 megohms) . pin 24 and the ground (>10 megohms) . pin 23 and the ground (>10 megohms).
1 If the resistance values are out of the specified limits:
_
- with the thrust reverser blocker doors in the stowed position, disconnect the harnesses J5 and J6 from each stow switch,
- do a resistance check on each stow switch between: . pins 4 and 7 (>10 megohms) . pins 4 and 9 (<5 ohms) . pin 4 and the ground (>10 megohms) . pins 4 and 12 (>10 megohms) . pins 2 and 3 (>10 megohms) . pins 2 and 5 (<5 ohms) . pin 2 and the ground (>10 megohms) . pins 2 and 1 (>10 megohms).
a If the resistance values are out of the specified limits:
_
- replace the defective: . SW-BLOCKER DOOR STOW, UPPER R (4104KS1) or/and . SW-BLOCKER DOOR STOW, LOWER R (4104KS2) or/and . SW-BLOCKER DOOR STOW, LOWER L (4104KS3) or/and . SW-BLOCKER DOOR STOW, UPPER L (4104KS4) (Ref. AMM TASK 78-31-18-000-040) and (Ref. AMM TASK 78-31-18-400-040).
b If the resistance values are in the specified limits:
_
- do a continuity and insulation check of the thrust reverser and harnesses J5 and J6 between the stow switches including the junction box (4100KS),
- do a visual check of each connector for correct condition.
c If damage is found:
_ - repair or replace as required.
d If nothing is found:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
F 『 EEFF : ALL E ∞∞78-31-00∞∞∞∞∞∞∞∞∞∞Page 256
E E May 01/05 ERE
ECES F 『 E C F M E E E E 56 E E E 2 If the resistance values are in the specified limits:
_
- with the thrust reverser blocker doors deployed, disconnect the harnesses J5 and J6 from each stow switch,
- do a resistance check on each stow switch (Ref. AWM 71-51-05) between: . pins 4 and 7 (<5 ohms) . pins 4 and 9 (>10 megohms) . pin 4 and the ground (>10 megohms) . pins 4 and 12 (>10 megohms) . pins 2 and 3 (<5 ohms) . pins 2 and 5 (>10 megohms) . pin 2 and the ground (>10 megohms) . pins 2 and 1 (>10 megohms).
a If the resistance values are out of the specified limits:
_
- replace the defective: . SW-BLOCKER DOOR STOW, UPPER R (4104KS1) or/and . SW-BLOCKER DOOR STOW, LOWER R (4104KS2) or/and . SW-BLOCKER DOOR STOW, LOWER L (4104KS3) or/and . SW-BLOCKER DOOR STOW, UPPER L (4104KS4) (Ref. AMM TASK 78-31-18-000-040) and (Ref. AMM TASK 78-31-18-400-040).
b If the resistance values are in the specified limits:
_
- do a continuity and insulation check of the thrust reverser and harnesses J5 and J6 between the stow switches including the junction box (4100KS),
- do a visual check of each connector for correct condition.
c If damage is found:
_ - repair or replace as required.
d If nothing is found:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(2) If the test does not give the maintenance message STOW SW, J5/J6, ECU:
(a) Do a check of the connectors of the thrust reverser harness, harnesses J5 and J6 for looseness, contamination, and bent pins.
1 If damage is found:
_
- retighten, clean or repair as required (Ref. AMM TASK 78-31-42-210-041).
F 『 EEFF : ALL E ∞∞78-31-00∞∞∞∞∞∞∞∞∞∞Page 257
E E May 01/05 ERE
ECES E 56 E E E
F 『
E C F M E
E E
(b) Do a check of the harness routing and look for chafing or cut in the harness envelope.
1 If damage is found:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 EXHAUST(28)
