- disconnect the harnesses J5 and J6 from the ECU (4000KS),
- do a resistance check of the harnesses J5 and J6 (Ref. AWM 71-51-05) between: . pins 21 and 22 (>10 megohms) . pins 21 and 11 (>10 megohms) . pin 21 and the ground (>10 megohms).
(a) If the resistance values are out of the specified limits:
- with the thrust-reverser blocker doors in the stowed position, disconnect the harnesses J5 and J6 from each deploy switch,
- do a resistance check on each deploy switch (Ref. AWM 71-51-05) between: . pins 3 and 2 (>10 megohms) . pins 4 and 5 (>10 megohms) . pins 4 and 1 (>10 megohms) . pin 4 and the ground (>10 megohms).
1_ If the resistance values are out of the specified limits:
- Inspect the deploy switches levers (Ref. AMM TASK 78-31-17-
210-040).
- If the finding do not indicate mechanical problem, replace
the defective:
. SW-BLOCKER DOOR DEPLOY, L (4103KS1) or/and
. SW-BLOCKER DOOR DEPLOY, R (4103KS2) (Ref. AMM TASK 78-31-
17-000-040) and (Ref. AMM TASK 78-31-17-400-040).
2 If the resistance values are in the specified limits:
_
- do a continuity and insulation check of the thrust reverser and harnesses J5 and J6 between the deploy switches including the junction box (4100KS) (Ref. ASM 73-25/16),
- do a visual check of each connector for correct condition.
a If damage is found:
_ - repair or replace as required.
b If nothing is found:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
F 『 EEFF : ALL E ∞∞78-31-00∞∞∞∞∞∞∞∞∞∞Page 264
E E May 01/05 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
(b) If the resistance values are in the specified limits:
- do a manual deployment of the thrust-reverser blocker doors (Ref. AMM TASK 78-32-41-860-001)
- do a resistance check of the harnesses J5 and J6 (Ref. AWM 71-51-05) between: . pins 21 and 22 (<5 ohms) . pins 21 and 11 (>10 megohms) . pin 21 and the ground (>10 megohms).
1 If the resistance values are out of the specified limits:
_
- with the thrust-reverser blocker doors in the stowed position, disconnect the harnesses J5 and J6 from each deploy switch,
- do a resistance check on each deploy switch (Ref. AWM 71-51-05) between: . pins 3 and 2 (<5 ohms) . pins 4 and 5 (<5 ohms) . pins 4 and 1 (>10 megohms) . pin 4 and the ground (>10 megohms).
a If the resistance values are out of the specified limits:
_
- Inspect the deploy switches levers (Ref. AMM TASK 78-31-17-210-040).
- If the finding do not indicate mechanical problem, replace the defective: . SW-BLOCKER DOOR DEPLOY, L (4103KS1) or/and . SW-BLOCKER DOOR DEPLOY, R (4103KS2) (Ref. AMM TASK 78-31-17-000-040) and (Ref. AMM TASK 78-31-17-400-040).
b If the resistance values are in the specified limits:
_
- do a continuity and insulation check of the thrust reverser and harnesses J5 and J6 between the deploy switches including the junction box (4100KS) (Ref. ASM 73-25/16),
- do a visual check of each connector for correct condition.
c If damage is found:
_
- repair or replace as required.
d If nothing is found:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
2 If the resistance values are in the specified limits:
_
- do a continuity and insulation check of the thrust reverser and harnesses J5 and J6 between the stow switches including the junction box (4100KS) (Ref. ASM 73-25/16),
- do a visual check of each connector for correct condition.
a If damage is found:
_
- repair or replace as required.
F 『 EEFF : ALL E ∞∞78-31-00∞∞∞∞∞∞∞∞∞∞Page 265
E E May 01/05 ERE ECES
F 『
E C F M E
E E
E 56 E
E E
b If nothing is found:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(2) If the test does not give the maintenance message DEPL SW, J5/J6, ECU:
- do a check of the connectors of the thrust reverser harness and harnesses J5 and J6 for looseness, contamination, and bent pins.
中國(guó)航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) EXHAUST(32)
