(k)
Remove actuator locks. Move flap lever to FLAPS UP detent. Check that LE and TE flaps retract and horn sounds.
NOTE: Depressurize hydraulic system prior to installation and removal of flap actuator locks.
(l)
Move flap lever between 1 and 25. Check that horn stops sounding.
(m)
Return flap handle to zero detent and release EPR test switch. Return thrust levers to idle stop. Check that horn is silent and EPR light goes out.
(9)
Test Speed Brake Arming Switch S276 (Fig. 502, Sheet 4)
(a) Perform test same as step 6.D.(5), Page 525.
(10)
Test Autobrake Off Ramp Switch S585 (if installed and connected).
(a)
Set speed brake lever to DOWN Position (Detail D, Fig. 502, Sheet 4).
(b)
Connect ohmmeter across terminals C and NO of switch and check for continuity between switch terminals.
(c)
Move speed brake lever aft until open circuit is obtained between switch terminals.
(d)
Check the speed brake lever is 3.28 to 3.84 inches aft from down and locked position.
(e)
Remove ohmmeter and set speed brake lever to down position.
(11)
Test parking brake input to Landing Gear Accessory Unit M338 (Airplanes incorporating SB 31-1049, SB 31-1054 or SB 31-1073)
(a)
Verify system A hydraulic power is available (Ref 27-51-0).
(b)
Position flaps to 5 units (Ref 27-51-0).
CAUTION: ENSURE THAT ALL PERSONNEL AND EQUIPMENT ARE CLEAR BEFORE MOVING CONTROL SURFACES.
(c)
Remove system A hydraulic power. Verify parking brake is released (Ref\32-44-0).
(d)
Verify that the speed brake lever on the P8 control stand is in the DOWN position.
(e)
Set the stabilizer trim control, on the P8 control stand, in the green band.
(f)
Advance both thrust levers into start of takeoff range.
(g)
On the engine accessory unit module, press and hold either of the engine pressure ratio (EPR) test switches.
(h)
Verify that the warning horn does not sound.
(i)
Release the EPR test switch.
(j)
Set the parking brake (Ref 32-44-0).
(k)
Press and hold either of the EPR test switches on the engine accessory unit module.
(l)
Verify that the warning horn sounds and that the parking brake light on the P8 control stand illuminates.
(m)
Release the parking brake.
(n)
Verify that the warning horn is silenced and that the parking brake light is
extinguished.
(o)
Release the EPR test switch.
(p)
Fully retard both thrust levers to idle position.
(q)
Restore airplane to normal.
(12)
Perform step 6.F. for airplanes with LE and TE Flap Aural Warning circuits.
501
Oct 20/91 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 31-26-0 Page 529
31-26-0 Apr 01/97
F. Test LE and TE Flap Aural Warning Circuits - Engines not running and airplane on theground using external power. (Airplanes with flaps LE WARNING TEST switches installed on E3-2 shelf/stanchion).
[Airplanes with and without EPR Activated T/O Warn System]
(1)
If not already done, disconnect the D770 connector from the V47 ground interconnect valve.
(2)
Provide trailing edge flap system A hydraulic power (Ref 27-51-0 MP or 29-11-0 MP) if necessary.
(3)
Place stabilizer so that stabilizer position indicator pointer is within one unit of center of green band.
(4)
Place speed brake lever in zero degree detent position.
(5)
Verify thrust levers are at idle and flaps are fully retracted.
(6)
Close the following circuit breakers on P6 panel.
(a)
LE FLAP POSITION INDICATOR - DC
(b)
LE FLAP POSITION INDICATOR - AC
(c)
MASTER DIM (section 6)
(d)
LANDING GEAR LIGHTS
(e)
AURAL WARNING
(f)
On airplanes with EPR activated take-off warning system,
1) ENG NO. 1 EPR AND LG WARNING
2) ENG NO. 2 EPR AND LG WARNING
3) EPR WARNING
(7)
Warning horn remains silent at completion of circuit breaker closures in previous step (4).
(8)
On airplanes with EPR activated take-off warning system only, open ENG NO. 1 EPR AND LG WARNING and ENG NO. 2 EPR AND LG WARNING circuit breakers. Horn shall remain silent.
(9)
Fully advance both throttle levers. The intermittent horn shall sound.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 儀表和面板(42)
