05-51-54
ALL ú ú 01 Page 201 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(5) S 212-019Examine the landing gear assemblies, related components and hydraulic lines for damage and/or hydraulic fluid leakage.
(6) S 212-020Examine the wheel well doors and wheel well door actuating rods for damage and/or blockage from pieces of the tire.
(7) S 212-021Examine the other tires for possible damage (AMM 32-45-00/601).
NOTE:____ Carefully inspect the other tires for slash and/or wire penetration damage of the tread or the sidewall.
(8) S 212-022Examine the engine nacelles and inlets (Ref Chapter 72) for damage when the nose gear tire tread is lost or the nose gear tire burst.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
05-51-54
ALL ú ú 01 Page 202 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FLAT SPOTTED TIRES - MAINTENANCE PRACTICES (CONDITIONAL INSPECTION)
___________________________________________________________________
1. General_______
A. Examine the wheel and brake components and systmes after tires become flat spotted. The tires are damaged when a locked wheel slides (not a tire structural failure) and the cause is not apparent. Examine in the sequence in this section.
B. The examinations are divided into two phases. Phase I examinations are for conditions where only one tire is flat spotted. Phase II examinations are for conditions where more than one tire is flat spotted.
TASK 05-51-55-212-001
2. Flat Spotted Tires Conditional Inspection_________________________________________
A. References
(1)
AMM 29-15-61/201, Hydraulic Return Filter
(2)
AMM 32-41-41/601, Main Gear Wheel Brakes
(3)
AMM 32-42-00/501, Antiskid/Autobrake System
(4)
AMM 32-44-00/501, Parking Brake System
(5)
AMM 32-45-00/601, Wheels
B. Phase I One Flat Spotted Tire Examinations
S 712-002
(1)
Make sure the brake will operate correctly and is in a serviceable condition (AMM 32-41-41).
S 212-003
(2)
Examine the wheel for cracks or loose wheel bearings (AMM 32-45-00).
S 712-004
(3)
Make sure the brake releases correctly (AMM 32-42-00).
S 212-005
(4)
Make sure the routing of the hydraulic lines and the wiring runs are correct.
S 712-006
(5)
Do the transducer spin test and make sure that the correct brake releases when the transducer motion stops (AMM 32-42-00).
C. Phase II More Than One Flat Spotted Tire Examinations
S 712-007
(1)
Make sure the brakes will operate correctly and are in a serviceable condition (AMM 32-41-41).
(2)
Make sure the brakes release correctly (AMM 32-42-00).
S 712-008
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
05-51-55
ALL ú ú 01 Page 201 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(3) S 212-009Make sure that the hydraulic return filter is not blocked (Ref 29-15-61).
(4) S 212-010Make sure the routing of the hydraulic lines and the wiring runs are correct.
(5) S 712-011Do the transducer spin test and make sure that the correct brake releases when the transducer motion stops (AMM 32-42-00).
(6) S 712-012Make sure the parking brake valve operates correctly (AMM 32-44-00).
(7) S 212-014Also make sure that the valve is fully open when the parking brake releases (AMM 32-44-00).
(8) S 742-013Do a BITE test for the Antiskid/Autobrake system and also make sure the system has continuity (AMM 32-42-00).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 TIME LIMITS/MAINTENANCE CHE(54)
