曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (a)  Examine the aluminum gaskets with imbedded flexible seal material for the limits that follow: 1) Examine for nicks, cuts, gouges or openings across the
 surface of the seal material. a) These are not permitted. 2) Examine for hard or brittle seal material. a) These are not permitted.
 3)  Examine the surface of the seal material for deformation that could cause a blockage of the seal. a) These are not permitted.
 4)  For the fuel pump or MEC gasket only, examine the seal material for a minimum of 0.018 inch (0.45 mm) above the aluminum surfaces.
 5)  Examine the full length of the seal surface.
 S 912-013-C00
 (5)  Maintenance of the Aluminum Gaskets
 (a)  
Remove the lifted metal in the bolt hole area with a fine polishing stone or equivalent. 1) Be careful not to cause damage to the seal material.

 (b)  
Cut all thin, lacy, seal material that extends beyond the normal seal material on the aluminum surfaces. 1) Be careful not to cut or loosen the bottom of the material.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-30-01
 ALL  ú ú C01 Page 202 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
FLUORESCENT-PENETRANT INSPECTION -
__________________________________ MAINTENANCE PRACTICES
_____________________
 ú1.ú General ú A. This procedure includes two tasks on how to do a fluorescent penetrant ú inspection. The first task is a portable post-emulsifiable inspection. ú The second task is a water washable inspection. ú B. CFMI recommends the operators use the portable post-emulsifiable system ú because the water washable inspection can remove the penetrant indication ú if too much water is used. ú C. It is permitted to substitute a penetrant system with a higher ú sensitivity (i.e. - substitute a level 3 or 4 for a level 2 as ú recommended) if the inspectors that do the inspection have a higher ú training, knowledge, techniques and experience in the interpretation of ú indications. The higher sensitivity level gives a higher background ú fluorescence contrast that can lead to irrelevant indications. ú ú TASK 70-40-01-202-038-C00 ú2.ú Fluorescent Penetrant Inspection (Portable Post-Emulsifiable) ú A. General ú (1) This is a post-emulsifiable fluorescent penetrant inspection process ú intended for inspections at remote locations. ú (a) Portable fluorescent penetrant inspection is a localized ú process, limited to small areas or spot inspection of specific ú areas of parts. It is not intended for normal inspection. ú (b) It is convenient to use for inspection of welded or other ú localized repair areas. ú (c) The penetrant is applied only to a local area that needs to be ú inspected. ú (2) If visible non-fluorescent color dye penetrant has been used on ú parts which are to be subsequently inspected with fluorescent ú penetrants, the contamination by the dye may prevent reliable ú fluorescent penetrant inspection. ú (3) Any color dye indications evident by white light visual inspection ú shall be considered valid indications even if not detectable by ú ultraviolet light. ú (4) Titanium alloy parts are subject to stress corrosion cracking when ú residues of halogen containing compounds remain on a part that is ú subsequently subjected to high temperatures typical of welding, heat ú treating, or engine operation. ú (a) These parts must be thoroughly cleaned with non-halogen ú compounds after exposure to any halogen containing compound to ú prevent cracking and possible failure of parts.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-40-01
 ALL  ú ú C01.1 Page 201 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
ú (b) When using water for processing parts made of titanium or ú titanium alloy, deionized water should be used when it is ú possible. ú (5) Make sure you obey these instructions: ú (a) Make sure the parts are clean before you start the inspection ú process. ú (b) Plug or cap all tubes or holes in parts in the area being ú inspected to prevent penetrant or other material becoming ú entrapped. ú (c) Fluorescent penetrants and developers used together in an ú inspection system should be products of one manufacturer, ú except when using solvent (non-aqueous) wet developer. It is ú permissible to use the approved solvent wet developer, ú Tracer-Tech D499C, with any product system. ú B. Equipment ú (1) Inspection Booth or Darkroom or Black Cloth Hood (for remote ú locations) which prevents excessive admission of white light ú         ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(55)