(c)
Make sure that all the internal areas and recesses are fully clean and dry. 1) Blow out the internal areas and recesses of the part with
dry air.
S 232-025-C00
(8) Quality Assurance
(a)
Examine the part below the ultraviolet light.
1) Make sure you remove all the penetrants and developer materials.
(b)
Make sure you remove the remaining compounds fully from the parts made of titanium and the titanium alloy.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-40-01
ú ALL ú
ú ú ú C01.101 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details. Page 212Jul 12/02
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
STANDARD TOOLS AND EQUIPMENT - MAINTENANCE PRACTICES
____________________________________________________
TASK 70-60-01-912-001-C00
1. Standard Tools and Equipment
____________________________
A. General
(1) This procedure contains the approved tools and equipment you use in the maintenance of the CFM56 engine.
B. Procedure
S 912-002-C00
(1) Use this List of Standard Tools and Equipment.
Description___________ Supplier
Bottles and Plastic Tubes in Local purchase
which to put Oil Samples
Vacuum Cleaner Local purchase
Heat Gun Local purchase
Feeler Gage Set Local purchase
Soft Nose Pliers Souriau Inc.
Model Souriau 7765 Kester Avenue
8498-03 Van Nuys, CA 91405 USA
Souriau Et Cie 9-13 Rue Gallieni 92103 Boulogne-Billancourt France
Crowfoot Wrench Snap-On Tools Company
Model Snap-On TMRX10 8049 28th Avenue
Kenosha, WI 53140 USA
Fork Wrench Snap-On Tools Company
Model Snap-On AN 8508-14 8049 28th Avenue
Kenosha, WI 53140 USA
3/8 inch Gimbal Joint Local purchase
3/8 inch Extension Bar Local purchase
3/8 inch Speeder Handle Local purchase
3/8 inch Drive Speedwrench Local purchase
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-60-01
ALL ú ú C01 Page 201 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
STANDARD ENGINE WIRING AND EQUIPMENT CHECK - MAINTENANCE PRACTICES
__________________________________________________________________
TASK 70-70-01-702-001-C00
1. Standard Engine Wiring And Equipment Check
A. General
(1)
This task has four topics:
(2)
The general instructions for the routing of the wiring harnesses.
(3)
The visual examination of the wiring harnesses.
(4)
A visual check of engine components, and harness connectors and receptacles.
(5)
The retention test for the connector sockets.
B. Consumable Materials
(1) B00682 Solvent, (CP2011) stoddard - PD 680, Type I or II
C. Access
(1) Location Zones
411 Engine 1 - Engine
421 Engine 2 - Engine
D. General Instructions On The Routing Of The Wiring Harnesses
S 822-002-C00
(1) Wire harness routing.
(a)
Make sure that all clamps are in their correct position and installed correctly.
(b)
Make sure that the wire bundle length is equally distributed between the attached parts and is not stressed.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(62)
