79-11-01
 ALL  ú ú C01 Page 704 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(c)
Disconnect the oil supply tube from the oil tank (Fig. 703).

 1)  Keep the bolts and the gasket for the subsequent installation.

 (d)  
Connect the oil service cart to the oil tank supply port.

 (e)  
Supply oil through the oil supply port at a maximum of 43.5 psig (3 bars) for 2 minutes.

 (f)  
Inspect the screen on the oil tank suction tube for
 cleanliness.

 (g)  
If the screen is not clean, continue to supply oil throught the oil supply port until the screen is clean.

 S 847-003-C00
 (4)  Put the airplane in a serviceable condition:
 (a)  
Disconnect the oil service cart from the oil tank supply port.

 (b)  
Engines with the self-sealing drain plug, do these steps (Fig. 701): 1) Install a new O-ring on the magnetic plug. 2) Install a new O-ring on the self-sealing drain plug. 3) Install the self-sealing plug. 4) Tighten the self-sealing plug to a torque of 361 to 398

 inch-pounds (41 to 45 Nm).
 5) Install the magnetic plug.

 (c)  
Engines with the drain plug, do these steps (Fig. 702): 1) Install a new O-ring on the drain plug. 2) Install the drain plug. 3) Tighten the drain plug to a torque of 361 to 398 inch-

pounds (41 to 45 Nm).

 (d)
Use the bolts and gasket seal to install the oil supply tube.

 1)  Tighten the bolts to a torque of 55 to 60 inch-pounds (6.3 to 6.8 Nm).

 (e)  
Fill the engine oil tank with oil (AMM 12-13-11/301).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-11-01
 ALL  ú ú C02 Page 705 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
OIL TANK - REPAIRS
__________________
 1.  General_______
 A. Repair of the oil tank is confined to the repair of the silicone layer.
 B. Repairs are done while the tank is on the engine.
 C. But, if a spare tank is available, think about replacement of the tank.
 NOTE: This is because of the time necessary for the layer to cure.
____
 TASK 79-11-01-308-001-C00
 2.  Silicone Layer Repair_____________________
 A. Consumable Materials
 (1)
Methyl Ethyl Ketone (MEK) - (CP 1040) (AMM 70-10-01/201)

 (2)
Primer SS4155 - (CP 2215) (AMM 70-10-01/201)

 (3)
Silicone RTV 577 - (CP 2214) (AMM 70-10-01/201)

 B. References
 (1) AMM 71-11-02/201, Fan Cowl Panels
 C. Access
 (1)  
Location Zones 506 Engine No. 1 - right side of the engine on the fan case 606 Engine No. 2 - right side of the engine on the fan case

 (2)  
Access Panels
 5737L Engine No. 1 - Right Fan Cowl Panel
 5837R Engine No. 2 - Right Fan Cowl Panel

 D. Procedure
 S 018-002-C00
 (1) Open the right fan cowl panel (AMM 71-11-02/201).
 S 158-003-C00
 CAUTION: DO NOT CAUSE DAMAGE TO THE TANK METAL SURFACE WHEN YOU REMOVE
_______
 THE LAYER.

 (2) Use a rotary wire brush to remove the loose layer.
 S 118-004-C00
 WARNING:_______DO NOT BREATHE THE GASES FOR A LONG TIME. METHYL ETHYL KETONE (MEK) IS POISONOUS AND MUST BE USED IN AN AREA SUFFICIENTLY OPEN TO THE AIR. IF YOUR SKIN TOUCHES MEK FOR A LONG TIME, MEK WILL:
 -BREAK DOWN SUBCUTANEOUS FAT
 -BREAKDOWN SKIN OIL
 -CAUSE DERMATITIS.
 (3) Fully clean the area to be repaired and the adjacent area with MEK.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-11-01
 ALL  ú ú C01 Page 801 ú Nov 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 滑油 OIL(16)