S 014-011

 (11)
 If a protective cover is installed on the external side of the drain mast, remove the protective cover.

 S 024-012

 (12)
 Remove the drain mast.

 TASK 38-31-61-404-013
 3. Drian Mast Installation (Fig. 401)
_______________________
 A. Special Tools and Equipment
 (1)  G38003 Cover - Protective, Drain Mast
 (optional)

 B. Standard Tools and Equipment
 (1)  Sealing Gun (for applying sealant)
 C. Consumable Materials
 (1)  
G01043 Cloth - Lint-free, commercially
 available

 (2)  
G02193 Cloth - Abrasive crocus 320 grit,
 commercially available

 (3)  
A00247 Sealant - BMS 5-95 Class B 1/2

 (4)  
G00270 Tape - Masking (for drain mast
 protective cover), commercially available

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ú

 38-31-61
 ú ú 02 Page 403 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (5)  B00148 Solvent - Methyl Ethyl Ketone (MEK),
 TT-M-261

 D. References
 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 30-71-01/401, Ribbon Heaters

 (3)  
WDM 30-71-11, 30-71-12

 E. Access
 (1)  
Location Zones 123 Forward Cargo Container Compartment Aft Half, Left 191 Fairing Wing to Body, Forward Lower Half L

 (2)  
Access Panels
 191T Access Panel, Drain Mast

 F. Procedure
 S 144-014
 (1)  Remove the remaining sealant from the inboard and outboard sides of the mounting hole for the drain mast.
 S 114-035
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (2)  
Clean each side of the mounting hole for the drain mast with BMS 11-7, FCC-55, MEK:Sec-Butyl alcohol (42:58), MEK, or MPK.

 S 434-015

 (3)  
Put the drain mast tube through the hole in the outer side of the airplane and align the bolt holes.

 (4)  
Install the mounting bolts, nuts, and washers.

 (5)  
Connect the drain line tubing to the drain mast.

 (6)  
Tighten the tubing clamp.

 S 434-016
 S 434-017
 S 434-018
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ú

 38-31-61
 ú ú 03 Page 404 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (7)  S 434-019Connect the electrical wires for the drain mast heater.
 (8)  S 434-020Clean the terminal and mount plate for the bonding jumper.
 (9)  S 434-021Connect the bonding jumper for the drain mast.
 S 434-022

 (10)
 If it is removed, replace the ribbon heater around the drain tubing (AMM 30-71-01/401).

 S 414-023

 (11)
 Replace the insulation blankets on the area around the drain mast if the blankets are removed.

 S 394-024

 (12)
 Apply the BMS 5-95 sealant and make a fillet seal between the edge of the drain mast and the outer side of the airplane.

 NOTE: Refer to BAC 5030 when you make the fillet seal and keep the
____ radius of the seal less than 0.12 inch.
 S 864-025
 (13) Remove the DO-NOT-CLOSE tags and close these circuit breakers:
 (a)  P414 Power Distribution Panel - Left 1) 414A24, WASTE & WTR LINE HTRS - MAIN POWER 2) 414C21, DRAIN MAST HEATERS - GROUND SERVICE MODE 3) 414D5, WASTE & WTR LINE HTRS - MAIN POWER 4) 414L23, DRAIN MAST HEATER - AIR - CENTER
 S 864-026
 (14)
 Supply electrical power (AMM 24-22-00/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 氣動系統(tǒng) WATER/WASTE(46)