S 825-021-N00
 (25)
 Lift the reverse thrust lever 6.0 degrees from the idle/stow position.

 S 825-034-N00

 (26)
 Release the reverse thrust lever.

 (a)  Make sure the reverse thrust lever moves in a positive
 direction to the idle/stow position.

 S 715-022-N00
 (27)
 Make sure that the movement of the reverse thrust lever moves smoothly and free of unusual noise through the full 89.25 degrees of movement.

 S 845-043-N00

 (28)
 Do these steps to each of the connectors that follow to move the interlock actuator back to the retract position:

 -
Thrust Lever 1 - DM7986

 -
Thrust Lever 2 - DM7987

 -
Thrust Lever 3 - DM7988

 -
Thrust Lever 4 - DM7989

 (a)  
Apply a ground to pins 8 and 10 of each connector.

 (b)  
Apply 28 volts dc power to pin 6 of each connector to retract the actuator.

 (c)  
Remove the 28 volts dc and the grounds from each connector.

 (d)  
Reconnect the connectors.

 S 715-023-N00
 (29)
 Push the go-around levers to make sure that the go-around levers and switch rollers operate freely.

 S 715-024-N00

 (30)
 Make sure the go-around levers go back to their initial position after they are operated.

 S 715-025-N00

 (31)
 Push the autothrottle disconnect levers, to make sure the autothrottle disconnect levers and switch rollers operate freely.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 76-11-01
 ALL  ú ú N02 Page 510 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 715-026-N00
 (32)
 Make sure the autothrottle disconnect levers go back to their initial position after they are operated.

 S 715-027-N00

 (33)
 Make sure the reverse thrust lever No. 2 lifts the speed brake lever out of the detent freely and without unusual noise.

 S 715-028-N00

 (34)
 Make sure the reverse thrust lever No. 4 lifts the speed brake lever out of the detent freely and without unusual noise.

 S 715-029-N00

 (35)
 Make sure that the reverse thrust lever operates the switch for the auto speed brake (S861), correctly (AMM 27-62-09/401).

 S 435-030-N00

 (36)
 Install the side panels of the control stand, thrust lever cover for the control stand, and switch covers for the thrust lever assembly (AMM 76-11-03/201).

 S 045-036-N00

 (37)
 Do the activation procedure for the autothrottle servomotor (AMM 76-11-03/201).

 S 865-035-N00

 (38)
 Supply electrical power to the flap lever RVDT, operation circuits for the speed brake lever, and thrust lever switches (AMM 76-11-03/201).

 S 865-032-N00

 (39)
 Do the activation procedure for the captain and first officer seats (AMM 76-11-03/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 76-11-01
 ALL  ú ú N02 Page 511 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
THRUST LEVER POSITION RESOLVER - REMOVAL/INSTALLATION
_____________________________________________________
 1.  General
_______
 A.  This procedure has two tasks. The first task gives instructions to
 remove the position resolver for the thrust levers. The second task
 gives instructions to install the position resolver for the thrust
 levers.

 B.  The position resolver for the thrust levers will be referred to as the
 resolver in this procedure.

 TASK 76-11-02-004-001-N00
 2.  Remove the Thrust Lever Position Resolver
_________________________________________
 A.  References
 (1)  
AMM 25-22-01/401, Main Passenger Cabin Ceiling Panels

 (2)  
AMM 76-11-03/201, Control Stand

 (3)  
IPC 76-11-02, Fig. 1

 B.  Access
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(12)